Google Pixel 4 Right Grip Sensor Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          1 - 3 hours

Sections

SIM Card Tray
1 step
Back Panel
20 steps
Battery
3 steps
Google Pixel 4 Disassembly (Post-Battery Removal)
16 steps
Right Grip Sensor
3 steps

Flags

BackGoogle Pixel 4
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

Use this guide to replace the right grip sensor and flex cable in your Google Pixel 4.

For your safety, discharge your battery below 25% before disassembling your phone. This reduces the risk of a dangerous thermal event if the battery is accidentally damaged during the repair.

This procedure will almost always destructively remove the Pixel 4’s grip sensors. The sensors are strongly adhered to the phone’s midframe and will usually come out in pieces. Before you begin this procedure, be sure to have replacement parts.

Caution: Google warns that disassembly of the front laser assembly could result in hazardous exposure to invisible infrared laser emissions. Read their safety warnings here.

Warning: Do not reuse the battery if it has been deformed or damaged, as doing so is a potential safety hazard. Replace it with a new battery.

What you need

Step 1

              Remove the SIM card tray

Insert a SIM eject tool, bit, or a straightened paper clip into the small hole on the SIM card tray on the left edge of the phone.
Press firmly to eject the tray.
Remove the SIM card tray.

Insert a SIM eject tool, bit, or a straightened paper clip into the small hole on the SIM card tray on the left edge of the phone.

Press firmly to eject the tray.

Remove the SIM card tray.

1024

Step 2

              Heat the back panel glass

Prepare an iOpener and apply it to the bottom edge of the back panel for one minute.
A hair dryer, heat gun, or hot plate may also be used, but be careful not to overheat the phone—the display and internal battery are both susceptible to heat damage.

Prepare an iOpener and apply it to the bottom edge of the back panel for one minute.

A hair dryer, heat gun, or hot plate may also be used, but be careful not to overheat the phone—the display and internal battery are both susceptible to heat damage.

Step 3

              Apply a suction cup

Apply a suction cup to the heated edge of the back panel by pressing down on it to create suction, as close to the edge as possible.
If your back glass is badly cracked, covering it with a layer of clear packing tape may allow the suction cup to adhere. Alternatively, very strong tape may be used instead of the suction cup. If all else fails, you can superglue the suction cup to the broken panel.

Apply a suction cup to the heated edge of the back panel by pressing down on it to create suction, as close to the edge as possible.

If your back glass is badly cracked, covering it with a layer of clear packing tape may allow the suction cup to adhere. Alternatively, very strong tape may be used instead of the suction cup. If all else fails, you can superglue the suction cup to the broken panel.

Step 4

              Insert an opening pick

Pull up on the suction cup with strong, steady force to create a gap between the back panel and the frame.
Depending on the age of your phone, this may be difficult. If you are having trouble, apply more heat to the edge and try again.
Insert the point of an opening pick into the gap.

Pull up on the suction cup with strong, steady force to create a gap between the back panel and the frame.

Depending on the age of your phone, this may be difficult. If you are having trouble, apply more heat to the edge and try again.

Insert the point of an opening pick into the gap.

Step 5

              Begin to slice the adhesive

Slide the opening pick across the bottom towards the left corner to slice the adhesive.
With the pick still inserted, slide it from the bottom left corner over to the bottom right corner to completely slice the bottom side adhesive.
Leave the pick inserted in the bottom right corner to prevent the adhesive from re-sealing.

Slide the opening pick across the bottom towards the left corner to slice the adhesive.

With the pick still inserted, slide it from the bottom left corner over to the bottom right corner to completely slice the bottom side adhesive.

Leave the pick inserted in the bottom right corner to prevent the adhesive from re-sealing.

Step 6

              Slice the lefthand-side adhesive

Prepare an iOpener and apply it on the left edge of the phone for one minute.

Prepare an iOpener and apply it on the left edge of the phone for one minute.

Step 7

Insert a second opening pick underneath the back panel directly over the charge port.
Slide the opening pick to the bottom left corner of the phone.

Insert a second opening pick underneath the back panel directly over the charge port.

Slide the opening pick to the bottom left corner of the phone.

Step 8

Slide the opening pick around the bottom left corner and across the left side of the phone to slice the adhesive.
The adhesive can be very gummy. Push the pick in and out in a sawing motion to help with slicing.
Stop when you reach the top left corner, near the camera, and leave the pick inserted.

Slide the opening pick around the bottom left corner and across the left side of the phone to slice the adhesive.

The adhesive can be very gummy. Push the pick in and out in a sawing motion to help with slicing.

Stop when you reach the top left corner, near the camera, and leave the pick inserted.

Step 9

              Slice righthand-side adhesive

Prepare an iOpener and apply it on the right edge of the phone for one minute.

Prepare an iOpener and apply it on the right edge of the phone for one minute.

Step 10

With the first two opening picks still in place, insert a third pick on the lower part of the righthand side.
Slide the opening pick up towards the top of the phone, slicing the right side’s adhesive.
Stop when you reach the top right corner, and leave the pick inserted.

With the first two opening picks still in place, insert a third pick on the lower part of the righthand side.

Slide the opening pick up towards the top of the phone, slicing the right side’s adhesive.

Stop when you reach the top right corner, and leave the pick inserted.

Step 11

              Slice the top-side adhesive

Slide the third opening pick around the top right corner and across the top side of the phone, slicing the final strip of adhesive.

Slide the third opening pick around the top right corner and across the top side of the phone, slicing the final strip of adhesive.

Step 12

              Lift up the back panel

Once you have sliced around the perimeter of the phone, carefully lift the right edge of the back cover, opening it like a book.
Do not try to pull the panel all the way off yet, as it is still connected to the phone.

Once you have sliced around the perimeter of the phone, carefully lift the right edge of the back cover, opening it like a book.

Do not try to pull the panel all the way off yet, as it is still connected to the phone.

Step 13

Continue swinging open the back panel until you can rest it on the left edge the phone, being careful not to put any stress on the attached ribbon cable.
During reassembly, this is a good point to power on your phone and test all functions before re-sealing the back panel. Be sure to power your phone back down completely before you continue working.

Continue swinging open the back panel until you can rest it on the left edge the phone, being careful not to put any stress on the attached ribbon cable.

During reassembly, this is a good point to power on your phone and test all functions before re-sealing the back panel. Be sure to power your phone back down completely before you continue working.

Step 14

              Disconnect the battery

Remove the five T3 Torx screws securing the battery connector shield:
Four 4.0 mm screws
One 2.1 mm screw
Throughout this repair, keep track of each screw and make sure it goes back exactly where it came from.

Remove the five T3 Torx screws securing the battery connector shield:

Four 4.0 mm screws

One 2.1 mm screw

Throughout this repair, keep track of each screw and make sure it goes back exactly where it came from.

Step 15

Use a pair of tweezers to remove the battery connector shield.

Use a pair of tweezers to remove the battery connector shield.

Step 16

Whenever you use the spudger near the battery, be very careful not to puncture the battery.
Using the pointed end of a spudger, pry the battery connector straight up from the motherboard to disconnect the battery.
To re-attach press connectors like this one, carefully align and press down on one side until it clicks into place, then repeat on the other side. Do not press down on the middle. If the connector is misaligned, the pins can bend, causing permanent damage.

Whenever you use the spudger near the battery, be very careful not to puncture the battery.

Using the pointed end of a spudger, pry the battery connector straight up from the motherboard to disconnect the battery.

To re-attach press connectors like this one, carefully align and press down on one side until it clicks into place, then repeat on the other side. Do not press down on the middle. If the connector is misaligned, the pins can bend, causing permanent damage.

Step 17

Using the flat end of a spudger, gently fold the battery cable over so it doesn’t accidentally make contact during the rest of your repairs.

Using the flat end of a spudger, gently fold the battery cable over so it doesn’t accidentally make contact during the rest of your repairs.

Step 18

              Disconnect the back panel connector

Use a T3 Torx driver to remove the two 4 mm screws securing the back panel connector cover.

Use a T3 Torx driver to remove the two 4 mm screws securing the back panel connector cover.

Step 19

Use a pair of tweezers to remove the back panel connector cover.

Use a pair of tweezers to remove the back panel connector cover.

Step 20

Using the pointed end of a spudger, pry up and disconnect the back panel connector.

Using the pointed end of a spudger, pry up and disconnect the back panel connector.

Step 21

              Remove the back panel

Remove the back panel.
During reassembly, follow this guide to install custom-cut adhesives for your device.
Follow this guide if you are using a pre-cut adhesive card.

Remove the back panel.

During reassembly, follow this guide to install custom-cut adhesives for your device.

Follow this guide if you are using a pre-cut adhesive card.

Step 22

              Remove the adhesive strips

Pull on the yellow pull tab of the adhesive strip with steady force.
If the adhesive becomes hard to pull, you can roll it around a spudger and continue pulling.
Continue firmly pulling up on the adhesive strip with constant force. If you’re using a spudger, spin it every so often to keep the exposed section of the pull tab as short as possible.
This may take a lot of force.
These adhesive pull tabs are very prone to snapping in half during this process. Pull as slowly as possible.
If the adhesive pull tabs are not stretching, you can fill a plastic dropper or syringe with high concentration isopropyl alcohol and apply a few drops under the left edge of the battery. Give the alcohol a minute to weaken the battery adhesive.
Continue this process for each of the three pull tabs, until all are either out or have snapped in half.

Pull on the yellow pull tab of the adhesive strip with steady force.

If the adhesive becomes hard to pull, you can roll it around a spudger and continue pulling.

Continue firmly pulling up on the adhesive strip with constant force. If you’re using a spudger, spin it every so often to keep the exposed section of the pull tab as short as possible.

This may take a lot of force.

These adhesive pull tabs are very prone to snapping in half during this process. Pull as slowly as possible.

If the adhesive pull tabs are not stretching, you can fill a plastic dropper or syringe with high concentration isopropyl alcohol and apply a few drops under the left edge of the battery. Give the alcohol a minute to weaken the battery adhesive.

Continue this process for each of the three pull tabs, until all are either out or have snapped in half.

Step 23

              Remove the battery

If the battery tabs snapped during removal, insert an opening pick on the upper right edge of the battery, slicing the adhesive underneath.
Even if you successfully removed all three adhesive pull tabs, using an opening pick to dislodge the battery may be helpful.
Don’t insert the opening pick on or anywhere below the grip sensor cable, as the pick can damage the charge port flex cable located underneath the battery.

If the battery tabs snapped during removal, insert an opening pick on the upper right edge of the battery, slicing the adhesive underneath.

Even if you successfully removed all three adhesive pull tabs, using an opening pick to dislodge the battery may be helpful.

Don’t insert the opening pick on or anywhere below the grip sensor cable, as the pick can damage the charge port flex cable located underneath the battery.

Step 24

Do not reuse the battery if it has been deformed or damaged, as doing so is a potential safety hazard. Replace it with a new battery.
Lift the battery up and away from the phone to remove it. You may need to peel the battery away from any leftover adhesive tabs.
If there’s any alcohol solution remaining in the phone, carefully wipe it off with a lint-free cloth or allow it to air dry before installing your battery.
To install a replacement battery:
If you’re using stretch release adhesive, apply them onto the battery. Otherwise, apply some double-sided tape, or pre-cut adhesive strips in the phone’s battery well, being careful not to cover the charge port flex cable. Peel away any tape liners to expose the adhesive.
Temporarily re-connect the battery’s connector to the motherboard socket. This ensures that the battery is properly positioned.
Lay the battery in place and press firmly.
Disconnect the battery connector from its motherboard socket and resume re-assembly.

Do not reuse the battery if it has been deformed or damaged, as doing so is a potential safety hazard. Replace it with a new battery.

Lift the battery up and away from the phone to remove it. You may need to peel the battery away from any leftover adhesive tabs.

If there’s any alcohol solution remaining in the phone, carefully wipe it off with a lint-free cloth or allow it to air dry before installing your battery.

To install a replacement battery:

If you’re using stretch release adhesive, apply them onto the battery. Otherwise, apply some double-sided tape, or pre-cut adhesive strips in the phone’s battery well, being careful not to cover the charge port flex cable. Peel away any tape liners to expose the adhesive.

Temporarily re-connect the battery’s connector to the motherboard socket. This ensures that the battery is properly positioned.

Lay the battery in place and press firmly.

Disconnect the battery connector from its motherboard socket and resume re-assembly.

Step 25

              Remove the screws securing the camera connector cover

Use a T3 Torx driver to remove the four 4 mm screws securing the camera connector cover.

Use a T3 Torx driver to remove the four 4 mm screws securing the camera connector cover.

Step 26

Using a pair of tweezers, tilt the camera cover up and slide it out of the retaining slot on the upper right corner of the phone to remove.

Using a pair of tweezers, tilt the camera cover up and slide it out of the retaining slot on the upper right corner of the phone to remove.

Step 27

              Disconnect the camera and sensor connectors

Using the pointed end of a spudger, pry the camera and sensor connectors straight up from the motherboard.

Using the pointed end of a spudger, pry the camera and sensor connectors straight up from the motherboard.

Step 28

Disconnect the additional sensor connector.

Disconnect the additional sensor connector.

Step 29

              Remove the front-facing camera and sensor assembly

Use a T3 Torx driver to remove the two 2.4 mm screws securing the front camera and sensor assembly.

Use a T3 Torx driver to remove the two 2.4 mm screws securing the front camera and sensor assembly.

Step 30

Use a pair of tweezers to remove the front camera and sensor assembly.

Use a pair of tweezers to remove the front camera and sensor assembly.

Step 31

              Remove the vibration motor cover

Remove the three T3 Torx screws securing the vibration motor cover:
One 4.2 mm screw
One 4.4 mm shouldered screw

Remove the three T3 Torx screws securing the vibration motor cover:

One 4.2 mm screw

One 4.4 mm shouldered screw

Step 32

Use a pair of tweezers to remove the vibration motor shield.

Use a pair of tweezers to remove the vibration motor shield.

Step 33

              Disconnect the motherboard press connectors

Use the pointed end of a spudger to disconnect the two rear-facing camera connectors from the motherboard.
Disconnect the side buttons connector from the motherboard.

Use the pointed end of a spudger to disconnect the two rear-facing camera connectors from the motherboard.

Disconnect the side buttons connector from the motherboard.

Step 34

Disconnect the earpiece speaker connector from the motherboard.

Disconnect the earpiece speaker connector from the motherboard.

Step 35

Disconnect the left grip sensor connector from the motherboard.
Disconnect the charge port connector from the motherboard.

Disconnect the left grip sensor connector from the motherboard.

Disconnect the charge port connector from the motherboard.

Step 36

Disconnect the right grip sensor connector from the motherboard.
Disconnect the display connector from the motherboard.

Disconnect the right grip sensor connector from the motherboard.

Disconnect the display connector from the motherboard.

Step 37

Use a pair of tweezers to disconnect the antenna connector from the charging assembly by pulling it straight up from the motherboard.

Use a pair of tweezers to disconnect the antenna connector from the charging assembly by pulling it straight up from the motherboard.

Step 38

Disconnect the bottom microphone connector from the motherboard.

Disconnect the bottom microphone connector from the motherboard.

Step 39

              Remove the motherboard

Slowly lift out the motherboard, being careful not to snag any ribbon cable connectors.
The rear-facing camera module connectors loop around the motherboard, and the camera module is not secured to the phone, so it may lift out with the motherboard during this step.
Completely remove the motherboard.
When reinstalling the motherboard, check that no ribbon cable connectors are caught underneath.

Slowly lift out the motherboard, being careful not to snag any ribbon cable connectors.

The rear-facing camera module connectors loop around the motherboard, and the camera module is not secured to the phone, so it may lift out with the motherboard during this step.

Completely remove the motherboard.

When reinstalling the motherboard, check that no ribbon cable connectors are caught underneath.

Step 40

              Remove the rear-facing camera module

Use a pair of tweezers to remove the rear-facing camera module.

Use a pair of tweezers to remove the rear-facing camera module.

Step 41

              Remove the right grip sensor

Use a pair of tweezers to peel the grip sensor flex cable off of the phone’s frame. It is secured with some light adhesive.
Continue peeling the flex cable until it is no longer adhered to the back side of the phone.

Use a pair of tweezers to peel the grip sensor flex cable off of the phone’s frame. It is secured with some light adhesive.

Continue peeling the flex cable until it is no longer adhered to the back side of the phone.

Step 42

Use a pair of tweezers to peel away the grip sensor from the inside edge of the phone’s frame.
This process is destructive, so proceed with caution, and have a replacement part ready.
Continue to peel away the grip sensor until it is no longer adhered to the inside frame.

Use a pair of tweezers to peel away the grip sensor from the inside edge of the phone’s frame.

This process is destructive, so proceed with caution, and have a replacement part ready.

Continue to peel away the grip sensor until it is no longer adhered to the inside frame.

Step 43

With the grip sensor peeled away from the inside edge, completely remove it.
Your grip sensor may come out in multiple pieces, so make sure there’s nothing left behind.
Remove any leftover adhesive before reinstalling a new grip sensor.

With the grip sensor peeled away from the inside edge, completely remove it.

Your grip sensor may come out in multiple pieces, so make sure there’s nothing left behind.

Remove any leftover adhesive before reinstalling a new grip sensor.

Compare your new replacement part to the original part—you may need to transfer remaining components or remove adhesive backings from the new part before installing.

To reassemble your device, follow the above steps in reverse order.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Try some basic troubleshooting, or ask our Answers community for help.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors

                    Carsten Frauenheim

Member since: 03/10/2020

81,713 Reputation

                                      330 Guides authored                  



                       Badges:
                       38







                                                        +35 more badges

Team

                       iFixit                        

                                                  Member of iFixit 



                    Community                     


                                            141 Members                     


                                            15,772 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team