Google Pixelbook Left Charging Port Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          5 - 20 minutes

Sections

Battery (Back Panel)
7 steps
Left Charging Port
8 steps

Flags

BackGoogle Pixelbook
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery (Back Panel)

Use the iFixit opening tools or a metal spudger to pry the rubber covers off the back of your Pixelbook.
Peel the linings off completely until the back of the Pixelbook looks bare.

Use the iFixit opening tools or a metal spudger to pry the rubber covers off the back of your Pixelbook.

Peel the linings off completely until the back of the Pixelbook looks bare.

1024

Step 2

Remove the two yellow 2.0mm screws by using a T3 Torx screwdriver.

Remove the two yellow 2.0mm screws by using a T3 Torx screwdriver.

Step 3

Remove the seventeen 3.0mm T5 Torx screws from the bottom panel.

Remove the seventeen 3.0mm T5 Torx screws from the bottom panel.

Step 4

Use the nylon spudger to pry the edge of the Pixelbook up until you can grab the edge with your fingers.
Open the back panel completely and lay it flat so you see the whole inside of the computer.

Use the nylon spudger to pry the edge of the Pixelbook up until you can grab the edge with your fingers.

Open the back panel completely and lay it flat so you see the whole inside of the computer.

Step 5

Remove the yellow 2.0mm screw from the middle of the panel by using the T3 Torx screwdriver to turn the screw counterclockwise.

Remove the yellow 2.0mm screw from the middle of the panel by using the T3 Torx screwdriver to turn the screw counterclockwise.

Step 6

Remove the small, black casing by using the spudger to lift it up from its place.

Remove the small, black casing by using the spudger to lift it up from its place.

Step 7

Disconnect the flat, black cord from the main component by using a spudger to push it out of the slot, or by using your hand to carefully pull it out.
Your back panel is now free from the main component.

Disconnect the flat, black cord from the main component by using a spudger to push it out of the slot, or by using your hand to carefully pull it out.

Your back panel is now free from the main component.

Step 8

              Left Charging Port

Remove the two 3.0mm silver screws from the thin, black component by using a T3 Torx screwdriver to turn the screws counterclockwise.

Remove the two 3.0mm silver screws from the thin, black component by using a T3 Torx screwdriver to turn the screws counterclockwise.

Step 9

Disconnect the thin, black and white cord from the motherboard by using the spudger to snap the connector up and out of place.

Disconnect the thin, black and white cord from the motherboard by using the spudger to snap the connector up and out of place.

Step 10

Remove the thin, black component by pulling it up and out of the laptop with your fingers.
This photo shows the bottom screw still in the black box, but yours should be removed.

Remove the thin, black component by pulling it up and out of the laptop with your fingers.

This photo shows the bottom screw still in the black box, but yours should be removed.

Step 11

Remove the gold 2.0mm corner screw by turning it counterclockwise with a T3 Torx screwdriver.

Remove the gold 2.0mm corner screw by turning it counterclockwise with a T3 Torx screwdriver.

Step 12

Using needle-nose tweezers, remove the silver casing by lifting it up and out of the computer.

Using needle-nose tweezers, remove the silver casing by lifting it up and out of the computer.

Step 13

Remove the three 3.0mm black screws on the right side by using a T5 Torx screwdriver to turn the screws counterclockwise.
Remove the silver 2.0mm screw on the left side by using a T3 Torx screwdriver to turn the screw counterclockwise.

Remove the three 3.0mm black screws on the right side by using a T5 Torx screwdriver to turn the screws counterclockwise.

Remove the silver 2.0mm screw on the left side by using a T3 Torx screwdriver to turn the screw counterclockwise.

Step 14

Disconnect the thin, black ribbon cable by using the spudger to lift it up from the computer.

Disconnect the thin, black ribbon cable by using the spudger to lift it up from the computer.

Step 15

Use the needle-nose tweezers to remove the charging port by lifting the component up and out of the Pixelbook.

Use the needle-nose tweezers to remove the charging port by lifting the component up and out of the Pixelbook.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors

                    Alon Gary

Member since: 01/24/2018

491 Reputation

                                      2 Guides authored                  



                       Badges:
                       5







                                                        +2 more badges

Team

                       Cal Poly, Team S18-G1, Livingston Winter 2018                        

                                                  Member of Cal Poly, Team S18-G1, Livingston Winter 2018 



                    CPSU-LIVINGSTON-W18S18G1                     


                                            4 Members                     


                                            7 Guides authored

kamil Szym - Sep 20, 2019

Where to get replacemt charging port from please

michaelnic - Jun 15, 2022

Where can we get a replacement charging port for the Pixelbook Go 2 (i7)?

Introduction#

What you need#

Team#

Introduction

What you need

Team