Difficulty
Moderate
Steps
10
Time Required
15 - 30 minutes
Sections
4
- Battery
- 1 step
- Stabilizer
- 2 steps
- Landing Gear
- 3 steps
- Arms
- 4 steps
Flags
0
BackGoPro Karma
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Hook your fingers on the tab and pull out the battery.
Hook your fingers on the tab and pull out the battery.
1024
Step 2
Stabilizer
- Locate stabilizer collar’s unlock and lock symbols. Twist the collar counterclockwise to unlock the stabilizer from GoPro Karma body.
- Place the GoPro Karma on a stable surface with the legs folded in and the stabilizer facing towards yourself.
Locate stabilizer collar’s unlock and lock symbols. Twist the collar counterclockwise to unlock the stabilizer from GoPro Karma body.
Place the GoPro Karma on a stable surface with the legs folded in and the stabilizer facing towards yourself.
Step 3
- Remove the stabilizer by pulling the entire stabilizer out of the drone body.
Remove the stabilizer by pulling the entire stabilizer out of the drone body.
Step 4
Landing Gear
- Flip the drone upside down with the landing gear out.
- Remove the four 1.2 cm long hex screws with a Hex 2.0 screwdriver in the four corners of the landing gear
Flip the drone upside down with the landing gear out.
Remove the four 1.2 cm long hex screws with a Hex 2.0 screwdriver in the four corners of the landing gear
Step 5
- Push with your thumb and pull up with your fingers to remove the landing gear.
- Caution: The landing gear is connected by a thin cable so do not pull too far away.
Push with your thumb and pull up with your fingers to remove the landing gear.
Caution: The landing gear is connected by a thin cable so do not pull too far away.
Step 6
- Flip over the landing gear and locate the cable connector.
- Use your thumbnail to disconnect the cable and free the landing gear.
Flip over the landing gear and locate the cable connector.
Use your thumbnail to disconnect the cable and free the landing gear.
Step 7
Arms
- Remove the two 1.2 cm long hex screws with a Hex 2.0 screwdriver and set them aside.
Remove the two 1.2 cm long hex screws with a Hex 2.0 screwdriver and set them aside.
Step 8
- Remove both locked connectors by pushing the connector release tool into the hole in the center and pulling up with the white handles.
- The connector release tool is only included with the purchase of a replacement arm from the GoPro website.
- If you do not have a connector release tool, use a small screwdriver to push each tab while pulling up with the white handles.
Remove both locked connectors by pushing the connector release tool into the hole in the center and pulling up with the white handles.
The connector release tool is only included with the purchase of a replacement arm from the GoPro website.
If you do not have a connector release tool, use a small screwdriver to push each tab while pulling up with the white handles.
Step 9
- Remove the cover plate by pulling up on the side.
- Feed each connector through the hole and set aside the cover plate.
Remove the cover plate by pulling up on the side.
Feed each connector through the hole and set aside the cover plate.
Step 10
- Loosen the 2 cm long hex screw in the arm with a Hex 2.0 screwdriver.
- The screw will not come out but loosen it until it can rotate easily.
- Pull up and off the broken arm.
Loosen the 2 cm long hex screw in the arm with a Hex 2.0 screwdriver.
The screw will not come out but loosen it until it can rotate easily.
Pull up and off the broken arm.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 2 other contributors
Kyle Hoff
Member since: 04/23/2018
141 Reputation
1 Guide authored
Badges:
4
+1 more badge
Team
Cal Poly, Team S25-G14, Maness Spring 2018
Member of Cal Poly, Team S25-G14, Maness Spring 2018
CPSU-MANESS-S18S25G14
4 Members
6 Guides authored
