Hannspree Hannspad Sn1At71 Battery Replacement Repair Guide

Difficulty

Moderate

Steps

9

Time Required

                          15 - 30 minutes            

Sections

2

• Back Panel
• 5 steps
• Battery
• 4 steps

Flags

0

• BackHannspree Hannspad SN1AT71

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

The battery replacement will require soldering. Soldering increases the difficulty of replacing the battery. For soldering assistance, there is a tutorial on the iFixit website.

If your battery is swollen, take appropriate precautions.

The battery can be refurbished, so don’t forget to recycle your battery.

What you need

Step 1

              Back Panel               

• Place the tablet screen side up.
• Make sure the device is turned off to avoid damage.

Place the tablet screen side up.

Make sure the device is turned off to avoid damage.

1024

Step 2

• Use the metal spudger to press an opening between the screen and back cover.
• The plastic tabs are located on each corner of the back cover.
• Be careful, as the plastic tabs are delicate.

Use the metal spudger to press an opening between the screen and back cover.

The plastic tabs are located on each corner of the back cover.

Be careful, as the plastic tabs are delicate.

Step 3

• Wedge the plastic opening tool between the screen and the back panel to prevent re-engagement

Wedge the plastic opening tool between the screen and the back panel to prevent re-engagement

Step 4

• Slide the metal spudger around the casing to separate it from the inside of the tablet.

Slide the metal spudger around the casing to separate it from the inside of the tablet.

Step 5

• Flip the tablet over so the screen side is down after all the tabs are separated.
• Remove the back panel by delicately lifting it straight up.

Flip the tablet over so the screen side is down after all the tabs are separated.

Remove the back panel by delicately lifting it straight up.

Step 6

              Battery               

• Remove the adhesive tape from the power connection cables.

Remove the adhesive tape from the power connection cables.

Step 7

• Instructions for desoldering can be found on the iFixit website.
• The soldering iron is hot. It can burn you and it can cause damage to the wires and motherboard.
• Grab hold of the red wire using the tweezers.
• Desolder the red wire connection from the motherboard using the tip of the soldering iron.
• Move the wire connection away from the motherboard.
• Do not let the red wire connection touch other wires or the motherboard.

Instructions for desoldering can be found on the iFixit website.

The soldering iron is hot. It can burn you and it can cause damage to the wires and motherboard.

Grab hold of the red wire using the tweezers.

Desolder the red wire connection from the motherboard using the tip of the soldering iron.

Move the wire connection away from the motherboard.

Do not let the red wire connection touch other wires or the motherboard.

Step 8

• Desolder the black and yellow wire connection from the motherboard by following the previous step.
• When moving the wire connections, do not let the red wire connection touch other wires or the motherboard.

Desolder the black and yellow wire connection from the motherboard by following the previous step.

When moving the wire connections, do not let the red wire connection touch other wires or the motherboard.

Step 9

• Insert the flat end of the nylon spudger between the battery and the case.
• The battery is connected to the tablet with an adhesive tape and will come free slowly.
• Do not puncture or bend the battery while removing. If your battery is swollen, take appropriate precautions.

Insert the flat end of the nylon spudger between the battery and the case.

The battery is connected to the tablet with an adhesive tape and will come free slowly.

Do not puncture or bend the battery while removing. If your battery is swollen, take appropriate precautions.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      8 other people completed this guide.                                             

Author

                                      with 10 other contributors 

                    matthew vandeventer                     

Member since: 03/11/2015

908 Reputation

                                      5 Guides authored                  



                       Badges:
                       19







                                                        +16 more badges                           

Team

                       Colorado Springs, Team 9-4, Panko Spring 2015                        

                                                  Member of Colorado Springs, Team 9-4, Panko Spring 2015 



                    UCCS-PANKO-S15S9G4                     


                                            3 Members                     


                                            10 Guides authored                     

Lawrence Pearce - Feb 6, 2017

Reply

Easy to follow,but, can’t find a battery anywhere, so really No use

Howard Eisenhut - Jul 13, 2017

Reply

Matthew,

Great job!!

I followed your instructions and no problem

Thanks

Me Eisenhut

mwause - Jan 26, 2020

Reply

Where can I buy a replacement battery?