Difficulty

Moderate

Steps

10

Time Required

                          20 - 25 minutes

Sections

4

  • Front Panel
  • 4 steps
  • Control Board
  • 3 steps
  • Circuit Board
  • 2 steps
  • Bluetooth Antenna
  • 1 step

Flags

1

This guide has been the hard work of our awesome students and is found to be exceptionally cool by the iFixit staff.

  • BackHarman Kardon Onyx Studio 2

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Front Panel
  • Using a plastic opening tool, pry off the front grill by wedging it in the notch on the front of the device.

Using a plastic opening tool, pry off the front grill by wedging it in the notch on the front of the device.

1024

Step 2

  • Remove the five 14.4 mm T10 Torx screws.

Remove the five 14.4 mm T10 Torx screws.

Step 3

  • Gently pull the front apart from the back.

Gently pull the front apart from the back.

Step 4

  • Remove the four wires connecting the front and back panels.
  • Pinch the connector tab and pull gently upwards.
  • Repeat for the other three connectors.

Remove the four wires connecting the front and back panels.

Pinch the connector tab and pull gently upwards.

Repeat for the other three connectors.

Step 5

              Control Board
  • Pull the silicone button band off of the outer edge of the speaker.

Pull the silicone button band off of the outer edge of the speaker.

Step 6

  • Disconnect the two pressure connections from the circuit board.

Disconnect the two pressure connections from the circuit board.

Step 7

  • Gently remove the control board band by placing fingers in contact with it through the button openings.
  • Work from the outer edges in so as not to bend the band.

Gently remove the control board band by placing fingers in contact with it through the button openings.

Work from the outer edges in so as not to bend the band.

Step 8

              Circuit Board
  • Disconnect the remaining connectors from the circuit board.
  • Disconnect the Bluetooth antenna.

Disconnect the remaining connectors from the circuit board.

Disconnect the Bluetooth antenna.

Step 9

  • Remove the four 10 mm T10 Torx screws.
  • Pull the circuit board out of the device as it is now free.

Remove the four 10 mm T10 Torx screws.

Pull the circuit board out of the device as it is now free.

Step 10

              Bluetooth Antenna
  • Using the wide blue plastic opening tool, gently peel back edges of the Bluetooth board.
  • Peel off completely and remove from the device.

Using the wide blue plastic opening tool, gently peel back edges of the Bluetooth board.

Peel off completely and remove from the device.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      3 other people completed this guide.

Author

                                      with 1 other contributor 


                    Alexandra Achtenberg

Member since: 02/02/2017

1,873 Reputation

                                      6 Guides authored                  



                       Badges:
                       16







                                                        +13 more badges

Team

                       USF Tampa, Team 16-5, Blackwell Spring 2017                        

                                                  Member of USF Tampa, Team 16-5, Blackwell Spring 2017 



                    USFT-BLACKWELL-S17S16G5                     


                                            3 Members                     


                                            24 Guides authored

Cort Krause - Feb 19, 2018

Reply

Any idea where we can purchase the replacement parts?