Featured

Featured Guide

Difficulty

Moderate

Steps

11

Time Required

Suggest a time??

Sections

1

  • Hemming Pants
  • 11 steps

Flags

2

Worn Wear

Patagonia and iFixit are celebrating the stories we wear by collaborating to provide guides for Patagonia’s most popular apparel repairs.

This guide has been found to be exceptionally cool by the iFixit staff.

  • BackPatagonia Bottoms

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

For replacement parts or further assistance, contact Patagonia Customer Service.

What you need

Step 1

              Hemming Pants
  • Begin by assessing the pants’ current length. This is best done by wearing the pants along with an appropriate pair of shoes.
  • Wearing pants barefoot or with high heels will affect their length relative to the floor.
  • It’s helpful to have a second person assist with this step and the two that follow.

Begin by assessing the pants’ current length. This is best done by wearing the pants along with an appropriate pair of shoes.

Wearing pants barefoot or with high heels will affect their length relative to the floor.

It’s helpful to have a second person assist with this step and the two that follow.

1024

Step 2

  • Fold the cuff of one pant leg inward, and adjust it to the desired length.
  • Insert two or three pins to hold the cuff in position.
  • The pins should be placed parallel to the new fold.
  • With the pins in place, verify that the length is correct.
  • Make any final adjustments to the length as needed.

Fold the cuff of one pant leg inward, and adjust it to the desired length.

Insert two or three pins to hold the cuff in position.

The pins should be placed parallel to the new fold.

With the pins in place, verify that the length is correct.

Make any final adjustments to the length as needed.

Step 3

  • On a flat, clean surface, lay the pants down on their side with the newly shortened pant leg on top.
  • Using a ruler, note the distance from the edge of the old cuff to the edge of the new cuff.
  • Repeat the measurement several times along the width of the cuff, making sure the new hemline is perfectly even.

On a flat, clean surface, lay the pants down on their side with the newly shortened pant leg on top.

Using a ruler, note the distance from the edge of the old cuff to the edge of the new cuff.

Repeat the measurement several times along the width of the cuff, making sure the new hemline is perfectly even.

Step 4

  • Thread the sewing machine, using a thread color that matches your garment’s fabric as closely as possible.
  • Sewing machine setup varies from one model to another. Consult your sewing machine manual for precise instructions.
  • Place the first cuff on the sewing machine, and position the sewing needle between one of your pins and the edge of the cuff.

Thread the sewing machine, using a thread color that matches your garment’s fabric as closely as possible.

Sewing machine setup varies from one model to another. Consult your sewing machine manual for precise instructions.

Place the first cuff on the sewing machine, and position the sewing needle between one of your pins and the edge of the cuff.

Step 5

  • Gently depress the foot pedal and begin sewing.
  • Be sure the needle penetrates the pant leg on only one side. It may be easier to position the pant leg around the arm of the sewing machine with the table removed. If you sew through both layers, you will sew the pant leg shut!
  • Pause when you reach a pin, and remove it before continuing.
  • Do not attempt to sew over any pins. Hitting a pin can bend or break the sewing machine needle.

Gently depress the foot pedal and begin sewing.

Be sure the needle penetrates the pant leg on only one side. It may be easier to position the pant leg around the arm of the sewing machine with the table removed. If you sew through both layers, you will sew the pant leg shut!

Pause when you reach a pin, and remove it before continuing.

Do not attempt to sew over any pins. Hitting a pin can bend or break the sewing machine needle.

Step 6

  • Continue sewing all the way around the cuff, until you reach the first few stitches.
  • Sew over the first few stitches to prevent the stitches from unraveling.

Continue sewing all the way around the cuff, until you reach the first few stitches.

Sew over the first few stitches to prevent the stitches from unraveling.

Step 7

  • Raise the presser foot, and remove the pants from the sewing machine.
  • Clip any threads.

Raise the presser foot, and remove the pants from the sewing machine.

Clip any threads.

Step 8

  • Turn the cuff over so that the extra length of the hem folds out.
  • Clip the extra length, leaving about a half inch of fabric beyond the seam.
  • Be sure to only cut through one layer of the fabric—the excess fabric. Do not cut through the pants.
  • This step is optional. If you are hemming pants for a growing kiddo, leaving the excess length allows you to rip the seam and magically lengthen the pants later on.

Turn the cuff over so that the extra length of the hem folds out.

Clip the extra length, leaving about a half inch of fabric beyond the seam.

Be sure to only cut through one layer of the fabric—the excess fabric. Do not cut through the pants.

This step is optional. If you are hemming pants for a growing kiddo, leaving the excess length allows you to rip the seam and magically lengthen the pants later on.

Step 9

  • Set your sewing machine to a zigzag stitch.
  • Insert the freshly cut edge of the hem into the sewing machine.
  • Be sure to only insert one layer of fabric—the hem—or you will sew through the outer, visible layers of the pants.

Set your sewing machine to a zigzag stitch.

Insert the freshly cut edge of the hem into the sewing machine.

Be sure to only insert one layer of fabric—the hem—or you will sew through the outer, visible layers of the pants.

Step 10

  • Sew around the hem, as close to the edge as possible.
  • Zigzagging the edge prevents the edge from unraveling.

Sew around the hem, as close to the edge as possible.

Zigzagging the edge prevents the edge from unraveling.

Step 11

  • Lift the presser foot and remove the pants from the sewing machine.
  • Clip any excess threads.

Lift the presser foot and remove the pants from the sewing machine.

Clip any excess threads.

Repeat steps 5-19 for the second pant leg.

Cancel: I did not complete this guide.

                                                                                      6 other people completed this guide.

Author

                                      with 3 other contributors 


                    Brittany McCrigler

Member since: 03/05/2012

87,796 Reputation

                                      132 Guides authored                  



                       Badges:
                       48







                                                        +45 more badges

robert gelman - Dec 13, 2014

Reply

Perhaps a better idea: http://www.sewmuchado.com/2011/06/tutori…

Also: https://www.youtube.com/watch?v=BaoE5Juu…