Hipstreet Titan Plus Battery Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          15 minutes

Sections

Battery
5 steps

Flags

BackHipstreet Titan Plus
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

Battery percentage remains low, even after charging.The tablet dies when it still has a lot of battery life.The tablet becomes hot after using for a short period of time.

If you experience these symptoms, you might need to get a new battery. This battery replacement guide will walk you through the steps on how to remove necessary components in order to get to the battery. Replacing the battery is a moderate five step process using the necessary tools (refer to tools list).

What you need

Step 1

              Battery

Before beginning this process, make sure the device is powered off.
Use the plastic opening tools from iFixit to safely remove the screen from the back of the device.
Lift and remove screen to reveal the battery and circuit board as seen in the picture.

Before beginning this process, make sure the device is powered off.

Use the plastic opening tools from iFixit to safely remove the screen from the back of the device.

Lift and remove screen to reveal the battery and circuit board as seen in the picture.

1024

Step 2

Preparing to remove the speaker.
Use spudger to remove the speaker from the back casing of the device.
Note: Handle with care

Preparing to remove the speaker.

Use spudger to remove the speaker from the back casing of the device.

Note: Handle with care

Step 3

Remove the black strips as shown in the picture from the wires using the tweezers.
Be careful of handling, if not done correctly you will need to replace.

Remove the black strips as shown in the picture from the wires using the tweezers.

Be careful of handling, if not done correctly you will need to replace.

Step 4

Carefully use the spatula and spudger from iFixit to remove the battery from the device.
Note: The different color wires needs to be reconnected onto the proper terminals on the circuit board
Note: here is a how to solder and desolder connections guide to properly do step 5. How To Solder and Desolder Connections
Dispose of the old battery properly.

Carefully use the spatula and spudger from iFixit to remove the battery from the device.

Note: The different color wires needs to be reconnected onto the proper terminals on the circuit board

Note: here is a how to solder and desolder connections guide to properly do step 5. How To Solder and Desolder Connections

Dispose of the old battery properly.

Step 5

Heat the soldering iron to operating temperature.
Use caution as to not harm yourself when using the hot soldering iron.
Locate the black and red wires on the top of the circuit board.
Note: Remember the placement of the red and black wires on the circuit board.
Using the soldering iron, apply heat to the shiny solder point on the circuit board (Circled on the picture).
Note: Be sure not to break the wire when pulling the wires off. Let the solder melt in order to remove the wire.
Be sure to perform this task for both the black and red wires.
Note: If the iron is not hot enough, you might encounter unsuccessful removal of the wires. In order to correct this, let the soldering iron heat up completely to try this step again.

Heat the soldering iron to operating temperature.

Use caution as to not harm yourself when using the hot soldering iron.

Locate the black and red wires on the top of the circuit board.

Note: Remember the placement of the red and black wires on the circuit board.

Using the soldering iron, apply heat to the shiny solder point on the circuit board (Circled on the picture).

Note: Be sure not to break the wire when pulling the wires off. Let the solder melt in order to remove the wire.

Be sure to perform this task for both the black and red wires.

Note: If the iron is not hot enough, you might encounter unsuccessful removal of the wires. In order to correct this, let the soldering iron heat up completely to try this step again.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 5 other contributors

                    Justin Machnik

Member since: 10/30/2015

194 Reputation

                                      1 Guide authored                  



                       Badges:
                       7







                                                        +4 more badges

Team

                       UMass Dartmouth, Team 1-1, Miles Fall 2015                        

                                                  Member of UMass Dartmouth, Team 1-1, Miles Fall 2015 



                    UMASSD-MILES-F15S1G1                     


                                            3 Members                     


                                            10 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team