Difficulty

Moderate

Steps

13

Time Required

                          20 - 40 minutes

Sections

4

  • Disconnect Spark Plug
  • 1 step
  • Air Filter
  • 2 steps
  • Air Cleaner Housing
  • 4 steps
  • Clutch Cable
  • 6 steps

Flags

0

  • BackHonda Light Duty Tiller F220

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Disconnect the spark plug
  • Before you begin, make sure the engine is switched off and cool to the touch.
  • Pull the spark plug connector straight off of the spark plug.

Before you begin, make sure the engine is switched off and cool to the touch.

Pull the spark plug connector straight off of the spark plug.

1024

Step 2

              Remove the air filter
  • Push down on the two tabs at the top of the air filter cover.
  • With the two tabs depressed, swing the top of the cover down.
  • Remove the cover.

Push down on the two tabs at the top of the air filter cover.

With the two tabs depressed, swing the top of the cover down.

Remove the cover.

Step 3

  • Pull the air filter out of the housing and remove it.

Pull the air filter out of the housing and remove it.

Step 4

              Unscrew the air cleaner housing
  • Use an 8 mm socket to remove the following fasteners securing the air cleaner housing:
  • Two silver nuts
  • One black bolt

Use an 8 mm socket to remove the following fasteners securing the air cleaner housing:

Two silver nuts

One black bolt

Step 5

              Disconnect the breather tubes
  • Slide the pink breather tube out of its clip on the back of the air cleaner housing.

Slide the pink breather tube out of its clip on the back of the air cleaner housing.

Step 6

  • Use a flathead screwdriver to gently pry the black breather tube off of its connector on the back of the air cleaner housing.

Use a flathead screwdriver to gently pry the black breather tube off of its connector on the back of the air cleaner housing.

Step 7

              Remove the air cleaner housing
  • Hold the black carburetor hose in place and rotate the air cleaner housing clockwise until you can slide the hose out of its slot on the air cleaner housing.
  • Remove the air cleaner housing.

Hold the black carburetor hose in place and rotate the air cleaner housing clockwise until you can slide the hose out of its slot on the air cleaner housing.

Remove the air cleaner housing.

Step 8

              Loosen the clutch cable barrel adjuster
  • Use an 8 mm wrench to hold the clutch cable barrel adjuster in place while you use a 10 mm wrench to loosen the lock nut.
  • Continue to loosen the lock nut until it is against the end of the threads.
  • With the lock nut against the end of the threads, tighten the barrel until it is against the lock nut to add as much slack as possible to the cable.

Use an 8 mm wrench to hold the clutch cable barrel adjuster in place while you use a 10 mm wrench to loosen the lock nut.

Continue to loosen the lock nut until it is against the end of the threads.

With the lock nut against the end of the threads, tighten the barrel until it is against the lock nut to add as much slack as possible to the cable.

Step 9

              Remove the clutch cable
  • Slide the clutch cable housing straight out of its hole in the clutch lever.
  • Rotate the cable and housing through the slot in the lever until the cable is perpendicular to the lever.

Slide the clutch cable housing straight out of its hole in the clutch lever.

Rotate the cable and housing through the slot in the lever until the cable is perpendicular to the lever.

Step 10

  • Slide the clutch cable through the slot in the clutch lever and remove it from the lever.

Slide the clutch cable through the slot in the clutch lever and remove it from the lever.

Step 11

  • Remove any zip-ties securing the clutch cable.

Remove any zip-ties securing the clutch cable.

Step 12

  • Slide the clutch cable housing out of its bracket on the tiller.
  • Slide the clutch cable through the slot in the bracket to free it.

Slide the clutch cable housing out of its bracket on the tiller.

Slide the clutch cable through the slot in the bracket to free it.

Step 13

  • Slide the clutch cable off of its hook on the clutch spring.
  • Remove the clutch cable.

Slide the clutch cable off of its hook on the clutch spring.

Remove the clutch cable.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 1 other contributor 


                    Adam O'Camb

Member since: 04/11/2015

173,479 Reputation

                                      418 Guides authored                  



                       Badges:
                       39







                                                        +36 more badges