Difficulty

Very difficult

Steps

15

Time Required

                          40 minutes

Sections

3

  • Brush Roller
  • 3 steps
  • Belt
  • 5 steps
  • Suction Motor
  • 7 steps

Flags

2

Action Shots

Be an action hero! This guide needs images that better demonstrate how to perform specific actions.

Missed a Step

Oops! This guide is currently missing some important steps.

  • BackHoover Power Path Pro Advanced

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Brush Roller
  • Unplug the vacuum cleaner from the wall outlet before starting. Make sure the water tanks are empty.
  • Lay the cleaner down horizontally with its wheels closest to the floor.

Unplug the vacuum cleaner from the wall outlet before starting. Make sure the water tanks are empty.

Lay the cleaner down horizontally with its wheels closest to the floor.

1024

Step 2

  • Hold the lower brush roll with both hands and pull outwards until it is detached.

Hold the lower brush roll with both hands and pull outwards until it is detached.

Step 3

  • Unscrew the 6 marked screws using a Phillips #2 head screwdriver.
  • Remove the brush roller.

Unscrew the 6 marked screws using a Phillips #2 head screwdriver.

Remove the brush roller.

Step 4

              Belt
  • Use a long #2 Philips head screwdriver to remove the 8 numbered screws on the bottom of the cleaner.

Use a long #2 Philips head screwdriver to remove the 8 numbered screws on the bottom of the cleaner.

Step 5

  • Pull the red handle shown to remove the front suction unit from the cleaner.

Pull the red handle shown to remove the front suction unit from the cleaner.

Step 6

  • Unscrew the Phillips #2 screw at the bottom of the hose.

Unscrew the Phillips #2 screw at the bottom of the hose.

Step 7

  • Push down on the handle release button. Pull and disconnect the edge of the top cover on the side of the handle release button.
  • Repeat the above step for the “On/Off” button.
  • When pulling the handle release button, make sure the top of the cleaner does not fall.

Push down on the handle release button. Pull and disconnect the edge of the top cover on the side of the handle release button.

Repeat the above step for the “On/Off” button.

When pulling the handle release button, make sure the top of the cleaner does not fall.

Step 8

  • Gently grab the belt and pry it off from the rollers.

Gently grab the belt and pry it off from the rollers.

Step 9

              Suction Motor
  • Unscrew two screws using Phillips #2 screwdriver.
  • Detach grey piece from vacuum.

Unscrew two screws using Phillips #2 screwdriver.

Detach grey piece from vacuum.

Step 10

  • Unscrew four screws using a Phillips 2 screwdriver.

Unscrew four screws using a Phillips 2 screwdriver.

Step 11

  • Pull out of base of vacuum.

Pull out of base of vacuum.

Step 12

  • Flip vacuum over and unscrew three screws with a Phillips #2 screwdriver.

Flip vacuum over and unscrew three screws with a Phillips #2 screwdriver.

Step 13

  • Unscrew two screws with Phillips #2 screwdriver.

Unscrew two screws with Phillips #2 screwdriver.

Step 14

  • Detach motor and unscrew two screws with a Phillips #2 screwdriver.

Detach motor and unscrew two screws with a Phillips #2 screwdriver.

Step 15

  • Pull the bottom section off.
  • Pull the cap off.

Pull the bottom section off.

Pull the cap off.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      4 other people completed this guide.

Author

                                      with 3 other contributors 


                    Jose Andres Gonzalez Valdes

Member since: 01/22/2018

682 Reputation

                                      5 Guides authored                  



                       Badges:
                       9







                                                        +6 more badges

Team

                       Cal Poly, Team S16-G5, Banghart Winter 2018                        

                                                  Member of Cal Poly, Team S16-G5, Banghart Winter 2018 



                    CPSU-BANGHART-W18S16G5                     


                                            5 Members                     


                                            15 Guides authored