Hot Tools Professional 1110 Disassembly Repair Guide

Difficulty

Easy

Steps

Time Required

                          30 minutes

Sections

Hot Tools Professional 1110 Disassembly
7 steps

Flags

BackHot Tools Professional 1110
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

• Heating coil burn out

• Temperature control switch burn out

• On/Off switch burn out

What you need

Step 1

              Hot Tools Professional 1110 Disassembly

Ensure that you have a clean work station, and that you can easily keep track of small, loose parts.
In addition, MAKE SURE IT IS UNPLUGGED FOR ALL FOLLOWING STEPS!

Ensure that you have a clean work station, and that you can easily keep track of small, loose parts.

In addition, MAKE SURE IT IS UNPLUGGED FOR ALL FOLLOWING STEPS!

1024

Step 2

Firmly grasp the end of the Iron with the black plastic cap on the heating element end.
With your free hand, use tweezers to firmly grasp the small retaining ring sitting between the heating element and the handle body.
Once you have a firm grasp, pull up on the retaining ring, and it should come loose.

Firmly grasp the end of the Iron with the black plastic cap on the heating element end.

With your free hand, use tweezers to firmly grasp the small retaining ring sitting between the heating element and the handle body.

Once you have a firm grasp, pull up on the retaining ring, and it should come loose.

Step 3

With the ring loose, turn the handle body over, and you will see three screw holes.
Take a PH1 screwdriver, and loosen up all three 6mm Phillips #1 screws in the handle body.

With the ring loose, turn the handle body over, and you will see three screw holes.

Take a PH1 screwdriver, and loosen up all three 6mm Phillips #1 screws in the handle body.

Step 4

Once the screws have been removed, set them aside and with a pry tool, firmly pull the handle body apart in half lengthwise.

Once the screws have been removed, set them aside and with a pry tool, firmly pull the handle body apart in half lengthwise.

Step 5

For removing the clamping mechanism, firmly grasp the iron in your hand by the handle body, and locate the screw as shown in the picture.
Remove the screw shown (8mm Phillips #2 Pan Head) and when finished do the same for the opposite side.

For removing the clamping mechanism, firmly grasp the iron in your hand by the handle body, and locate the screw as shown in the picture.

Remove the screw shown (8mm Phillips #2 Pan Head) and when finished do the same for the opposite side.

Step 6

Once both screws have been removed, continue to remove the top clamping half of the mechanism from the body of the Iron.

Once both screws have been removed, continue to remove the top clamping half of the mechanism from the body of the Iron.

Step 7

Rotate the handle, and remove the screw that holds on the spring mechanism for the clamp. This screw is a 8mm Phillips #2 Pan Head.
Once this step is fished your Hot Tools Professional 1110 will be fully disassembled and ready to have its components replaced.

Rotate the handle, and remove the screw that holds on the spring mechanism for the clamp. This screw is a 8mm Phillips #2 Pan Head.

Once this step is fished your Hot Tools Professional 1110 will be fully disassembled and ready to have its components replaced.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors

                    Sean Neal

Member since: 11/11/2017

101 Reputation

                                      1 Guide authored                  



                       Badges:
                       3

Team

                       IUPUI, Team S2-G2, Wilson Fall 2017                        

                                                  Member of IUPUI, Team S2-G2, Wilson Fall 2017 



                    IUPUI-WILSON-F17S2G2                     


                                            4 Members                     


                                            5 Guides authored

Sharon Gonzalez - Oct 11, 2020

How can I tighten the clamp?

Introduction#

What you need#

Team#

Introduction

What you need

Team