Difficulty

Difficult

Steps

7

Time Required

                          30 - 45 minutes

Sections

2

  • Hover-1 Chrome Disassembly
  • 3 steps
  • Left Gyroscope Sensor Board
  • 4 steps

Flags

1

Better Introduction

Improve this guide by completing or revising its introduction.

  • BackHover-1 Chrome

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Hover-1 Chrome Disassembly
  • Flip the Hover-1 Chrome upside down.
  • Use a Phillips #2 screwdriver to remove the fourteen 14 mm screws from the bottom of the Hover-1.
  • Break the two black tape circles, and remove the two 15 mm Phillips screws underneath.

Flip the Hover-1 Chrome upside down.

Use a Phillips #2 screwdriver to remove the fourteen 14 mm screws from the bottom of the Hover-1.

Break the two black tape circles, and remove the two 15 mm Phillips screws underneath.

1024

Step 2

  • Lift the shell without the speaker grille and unplug the battery.

Lift the shell without the speaker grille and unplug the battery.

Step 3

  • Lift the shell with the speaker grille.
  • Unplug the speaker.
  • Unplug the LEDs.
  • Unplug the power button
  • Unplug the charging port.

Lift the shell with the speaker grille.

Unplug the speaker.

Unplug the LEDs.

Unplug the power button

Unplug the charging port.

Step 4

              Left Gyroscope Sensor Board
  • Disconnect the speaker cable.
  • Disconnect the cable that travels to the other sensor board.

Disconnect the speaker cable.

Disconnect the cable that travels to the other sensor board.

Step 5

  • Disconnect the smaller connector midway on the cable.
  • Disconnect the larger connector midway on the cable.

Disconnect the smaller connector midway on the cable.

Disconnect the larger connector midway on the cable.

Step 6

  • Remove the four 12mm Phillips #2 screws securing the sensor board.

Remove the four 12mm Phillips #2 screws securing the sensor board.

Step 7

  • Locate the five solder locations on the underside of the gyroscope sensor board.
  • Plug in soldering iron and wait for the tip tip to reach its target temperature.
  • Rest the tip of the iron on the solder and wait for the solder to melt. The wire will drop out of the sensor board.
  • Be aware of where the tip of the soldering iron is at ALL times. Put on safety glasses before picking up the soldering iron. Turn on a fan and face it towards the device to vent harmful fumes away from the solderers face.

Locate the five solder locations on the underside of the gyroscope sensor board.

Plug in soldering iron and wait for the tip tip to reach its target temperature.

Rest the tip of the iron on the solder and wait for the solder to melt. The wire will drop out of the sensor board.

Be aware of where the tip of the soldering iron is at ALL times. Put on safety glasses before picking up the soldering iron. Turn on a fan and face it towards the device to vent harmful fumes away from the solderers face.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 4 other contributors 


                    Nick McGuire

Member since: 10/08/2018

551 Reputation

                                      4 Guides authored                  



                       Badges:
                       8







                                                        +5 more badges

Team

                       Cal Poly, Team S4-G1, White Fall 2018                        

                                                  Member of Cal Poly, Team S4-G1, White Fall 2018 



                    CPSU-WHITE-F18S4G1                     


                                            4 Members                     


                                            6 Guides authored