Difficulty

Easy

Steps

10

Time Required

                          25 - 50 minutes

Sections

2

  • Rear Wheel
  • 6 steps
  • Brake Pad
  • 4 steps

Flags

0

  • BackX Hover-1 Folding E-Scooter

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Rear Wheel
  • Remove either of the two 0.2 mm axle screws by using a hex bit 4.0 by turning clockwise.
  • The two screws are the same thread so find the screw that has the least torque. Only that screw will be able to removed in this step.
  • Turn the hex bit 4.0 counterclockwise to reassemble the axle screws.

Remove either of the two 0.2 mm axle screws by using a hex bit 4.0 by turning clockwise.

The two screws are the same thread so find the screw that has the least torque. Only that screw will be able to removed in this step.

Turn the hex bit 4.0 counterclockwise to reassemble the axle screws.

1024

Step 2

  • Slide off the plastic side panel.

Slide off the plastic side panel.

Step 3

  • Use a hex bit 4.0 to screw back in the 0.2 mm screw as tightly as possible by turning clockwise.
  • You will need to hold the other screw you are not replacing with an additional hex bit 4.0, so that the screws don’t spin freely.

Use a hex bit 4.0 to screw back in the 0.2 mm screw as tightly as possible by turning clockwise.

You will need to hold the other screw you are not replacing with an additional hex bit 4.0, so that the screws don’t spin freely.

Step 4

  • Flip over the scooter and use the hex bit 4.0 to remove the other 0.2 mm screw.

Flip over the scooter and use the hex bit 4.0 to remove the other 0.2 mm screw.

Step 5

  • Slide off the other plastic side panel.

Slide off the other plastic side panel.

Step 6

  • On the same side you removed the screw, use the bit extender to push down on the axle inside the wheel.
  • The axle pops out and the wheel easily comes off.
  • Two washers will pop out with the axle.

On the same side you removed the screw, use the bit extender to push down on the axle inside the wheel.

The axle pops out and the wheel easily comes off.

Two washers will pop out with the axle.

Step 7

              Brake Pad
  • Remove the two 25mm screws by twisting a Phillips #2 screwdriver counterclockwise.
  • Twist the screwdriver clockwise to reassemble.
  • There are also two nuts that secure the screws.

Remove the two 25mm screws by twisting a Phillips #2 screwdriver counterclockwise.

Twist the screwdriver clockwise to reassemble.

There are also two nuts that secure the screws.

Step 8

  • Wobble to remove the brake step.

Wobble to remove the brake step.

Step 9

  • Remove the two 8 mm screws by twisting a Phillips #2 screwdriver counterclockwise.
  • Twist the screwdriver clockwise to secure the screws.

Remove the two 8 mm screws by twisting a Phillips #2 screwdriver counterclockwise.

Twist the screwdriver clockwise to secure the screws.

Step 10

  • Remove the brake pad.

Remove the brake pad.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 1 other contributor 


                    Meagan Chan

Member since: 10/08/2018

112 Reputation

                                      1 Guide authored                  



                       Badges:
                       4







                                                        +1 more badge

Team

                       Cal Poly, Team S15-G5, White Fall 2018                        

                                                  Member of Cal Poly, Team S15-G5, White Fall 2018 



                    CPSU-WHITE-F18S15G5                     


                                            4 Members                     


                                            5 Guides authored

Olivia Joshua Samuel-Bolt - Jul 27, 2022

Reply

Hello, I have a hoverboard 1 scooter and I’ve charged it and it started going a couple days ago and then I came home and put it up and plugged it up for a couple hours and went to take off on it yesterday to go to a couple appointments and it would not go when I pushed off on it i only weight 128lbs so I know it’s not my weight but how long do I normally charge it or should charge it without messing the battery pack up because I took it to a friend who is an electrician that I bought it from and he said he didn’t know what could be wrong with it for me to call around to the scooter shops but no one has returned my calls and I need help with this matter asap if someone could please help me oh and also the scooter cuts on and shows 13 on the screen and as I push it it’ll change to 94 like how am I walking 94mph I don’t get it but the headlight works cause when I cut it on its bright and it cuts off when I hold the button but I also wanted to know if there was a reset button on this hoverboard 1 scooter