Hover 1 Folding E Scooter Deck Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          40 minutes - 1 hour

Sections

Rear Wheel
6 steps
Brake Pad
4 steps
Deck
3 steps

Flags

BackX Hover-1 Folding E-Scooter
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Rear Wheel

Remove either of the two 0.2 mm axle screws by using a hex bit 4.0 by turning clockwise.
The two screws are the same thread so find the screw that has the least torque. Only that screw will be able to removed in this step.
Turn the hex bit 4.0 counterclockwise to reassemble the axle screws.

Remove either of the two 0.2 mm axle screws by using a hex bit 4.0 by turning clockwise.

The two screws are the same thread so find the screw that has the least torque. Only that screw will be able to removed in this step.

Turn the hex bit 4.0 counterclockwise to reassemble the axle screws.

1024

Step 2

Slide off the plastic side panel.

Slide off the plastic side panel.

Step 3

Use a hex bit 4.0 to screw back in the 0.2 mm screw as tightly as possible by turning clockwise.
You will need to hold the other screw you are not replacing with an additional hex bit 4.0, so that the screws don’t spin freely.

Use a hex bit 4.0 to screw back in the 0.2 mm screw as tightly as possible by turning clockwise.

You will need to hold the other screw you are not replacing with an additional hex bit 4.0, so that the screws don’t spin freely.

Step 4

Flip over the scooter and use the hex bit 4.0 to remove the other 0.2 mm screw.

Flip over the scooter and use the hex bit 4.0 to remove the other 0.2 mm screw.

Step 5

Slide off the other plastic side panel.

Slide off the other plastic side panel.

Step 6

On the same side you removed the screw, use the bit extender to push down on the axle inside the wheel.
The axle pops out and the wheel easily comes off.
Two washers will pop out with the axle.

On the same side you removed the screw, use the bit extender to push down on the axle inside the wheel.

The axle pops out and the wheel easily comes off.

Two washers will pop out with the axle.

Step 7

              Brake Pad

Remove the two 25mm screws by twisting a Phillips #2 screwdriver counterclockwise.
Twist the screwdriver clockwise to reassemble.
There are also two nuts that secure the screws.

Remove the two 25mm screws by twisting a Phillips #2 screwdriver counterclockwise.

Twist the screwdriver clockwise to reassemble.

There are also two nuts that secure the screws.

Step 8

Wobble to remove the brake step.

Wobble to remove the brake step.

Step 9

Remove the two 8 mm screws by twisting a Phillips #2 screwdriver counterclockwise.
Twist the screwdriver clockwise to secure the screws.

Remove the two 8 mm screws by twisting a Phillips #2 screwdriver counterclockwise.

Twist the screwdriver clockwise to secure the screws.

Step 10

Remove the brake pad.

Remove the brake pad.

Step 11

              Deck

Hold the two 10mm nuts in place with a 10mm wrench.
Remove the two 33mm bolts connected to the 10 mm nuts by turning a hex 4.0 screwdriver counterclockwise.
The nuts are on the bottom of the deck.
Turn clockwise to reassemble the bolts.

Hold the two 10mm nuts in place with a 10mm wrench.

Remove the two 33mm bolts connected to the 10 mm nuts by turning a hex 4.0 screwdriver counterclockwise.

The nuts are on the bottom of the deck.

Turn clockwise to reassemble the bolts.

Step 12

Fold the scooter by releasing the latch and pushing the handlebars to the rear of the device.

Fold the scooter by releasing the latch and pushing the handlebars to the rear of the device.

Step 13

Hold the two hex nuts in place with a 10mm wrench.
Remove the next two 33 mm bolts attached to the 10 mm hex nuts by turning a hex 4.0 screwdriver counterclockwise.
The deck will fall off after you remove the final bolts.
Turn the hex bit clockwise to reassemble.

Hold the two hex nuts in place with a 10mm wrench.

Remove the next two 33 mm bolts attached to the 10 mm hex nuts by turning a hex 4.0 screwdriver counterclockwise.

The deck will fall off after you remove the final bolts.

Turn the hex bit clockwise to reassemble.

To reassemble your device, follow these instructions in reverse order and use the new deck instead.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 2 other contributors

                    Nicolo DiFronzo

Member since: 10/08/2018

229 Reputation

                                      2 Guides authored                  



                       Badges:
                       5







                                                        +2 more badges

Team

                       Cal Poly, Team S15-G5, White Fall 2018                        

                                                  Member of Cal Poly, Team S15-G5, White Fall 2018 



                    CPSU-WHITE-F18S15G5                     


                                            4 Members                     


                                            5 Guides authored

Original NYC ScooterCommuter - Oct 24, 2019

The latch does not operate properly and is missing a part on the right side so it cannot retract the steel bar that locks the position. What part do I need and can you pls send it? It’s a brand new unit.

Tiffany Trevino - May 10, 2021

step 7 is where mine is broken .. it was kicked hard and right after the 2 screws but before the curb has been snapped what do i do

Introduction#

What you need#

Team#

Introduction

What you need

Team