Hover 1 H1 Gyroscope Sensor Assemblies Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          15 minutes

Sections

Bottom Shell
4 steps
Gyroscope Sensor Assemblies
9 steps

Flags

BackHover-1 H1
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Bottom Shell

Remove the ten 9mm machine screws by using a long Phillips #2 screwdriver to rotate the screws counterclockwise.
Remove the twelve 9mm sheet metal screws by using a long Phillips #2 screwdriver to rotate the screws counterclockwise.

Remove the ten 9mm machine screws by using a long Phillips #2 screwdriver to rotate the screws counterclockwise.

Remove the twelve 9mm sheet metal screws by using a long Phillips #2 screwdriver to rotate the screws counterclockwise.

1024

Step 2

Puncture the two black stickers by using the tip of a screwdriver.
Remove the two 9mm machine screws by using a long Phillips #2 screwdriver to rotate the screws counterclockwise.

Puncture the two black stickers by using the tip of a screwdriver.

Remove the two 9mm machine screws by using a long Phillips #2 screwdriver to rotate the screws counterclockwise.

Step 3

Lift each side of the bottom shell by pulling up.
When lifting the shell, take care to not tear any cables from their connectors.

Lift each side of the bottom shell by pulling up.

When lifting the shell, take care to not tear any cables from their connectors.

Step 4

Unplug the battery by pulling gently on both sides of the orange connector.

Unplug the battery by pulling gently on both sides of the orange connector.

Step 5

              Gyroscope Sensor Assemblies

On the battery side of the hoverboard, remove the red, black, and purple sleeved cable from the sensor assembly by squeezing the tab and pulling up.

On the battery side of the hoverboard, remove the red, black, and purple sleeved cable from the sensor assembly by squeezing the tab and pulling up.

Step 6

Remove the red, blue, and green cable from the cable extension connected to the sensor assembly by squeezing the tabs on the side of the connector.

Remove the red, blue, and green cable from the cable extension connected to the sensor assembly by squeezing the tabs on the side of the connector.

Step 7

Remove the four 7mm screws by using a Phillips #2 screwdriver to rotate the screws counterclockwise.

Remove the four 7mm screws by using a Phillips #2 screwdriver to rotate the screws counterclockwise.

Step 8

Remove the sensor assembly on the battery side of the hoverboard by gently lifting and pulling away from the hoverboard.

Remove the sensor assembly on the battery side of the hoverboard by gently lifting and pulling away from the hoverboard.

Step 9

Remove the hot glue holding in the connectors with a utility knife.
Remove the white cable from the sensor assembly by squeezing the connector and pulling the connector up.
Be careful not to touch any parts of the circuit boards with the knife.

Remove the hot glue holding in the connectors with a utility knife.

Remove the white cable from the sensor assembly by squeezing the connector and pulling the connector up.

Be careful not to touch any parts of the circuit boards with the knife.

Step 10

Remove the red, blue, and green cable from the extension connected to the sensor assembly by squeezing the tabs on the side of the connector.

Remove the red, blue, and green cable from the extension connected to the sensor assembly by squeezing the tabs on the side of the connector.

Step 11

Remove the red and black sleeved connector from the sensor assembly by squeezing the tab and pulling up.

Remove the red and black sleeved connector from the sensor assembly by squeezing the tab and pulling up.

Step 12

Step 13

Remove the sensor assembly on the motherboard side of the hoverboard by gently lifting and pulling away from the hoverboard.

Remove the sensor assembly on the motherboard side of the hoverboard by gently lifting and pulling away from the hoverboard.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 4 other contributors

                    Aaron Teh

Member since: 10/08/2018

337 Reputation

                                      2 Guides authored                  



                       Badges:
                       6







                                                        +3 more badges

Team

                       Cal Poly, Team S17-G6, White Fall 2018                        

                                                  Member of Cal Poly, Team S17-G6, White Fall 2018 



                    CPSU-WHITE-F18S17G6                     


                                            4 Members                     


                                            7 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team