Difficulty
Moderate
Steps
12
Time Required
10 - 20 minutes
Sections
2
- Bottom Left Panel
- 3 steps
- Left Gyroscope and Motherboard
- 9 steps
Flags
0
BackHover-1 Titan
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Bottom Left Panel
- Flip the hoverboard so the bottom is facing up.
- The left side is the side that has the charge port. There is also an “L” on the metal plate underneath the wires.
Flip the hoverboard so the bottom is facing up.
The left side is the side that has the charge port. There is also an “L” on the metal plate underneath the wires.
1024
Step 2
- Using a Phillips #1 screwdriver, remove the two 14 mm screws located closest to the center of the hoverboard.
- Using a Phillips #1 screwdriver, remove the four 12 mm screws located in the middle of the panel.
- Using a Phillips #1 screwdriver, remove two 15 mm screws located closest to the wheel.
Using a Phillips #1 screwdriver, remove the two 14 mm screws located closest to the center of the hoverboard.
Using a Phillips #1 screwdriver, remove the four 12 mm screws located in the middle of the panel.
Using a Phillips #1 screwdriver, remove two 15 mm screws located closest to the wheel.
Step 3
- Grip the bottom left panel and lift up to remove.
Grip the bottom left panel and lift up to remove.
Step 4
Left Gyroscope and Motherboard
- Unplug the battery from the gyroscope by holding the yellow connector and pulling apart.
Unplug the battery from the gyroscope by holding the yellow connector and pulling apart.
Step 5
- Remove four 12 mm Phillips #1 head screws from the corners of the green gyroscope/motherboard.
Remove four 12 mm Phillips #1 head screws from the corners of the green gyroscope/motherboard.
Step 6
- Unplug the bottom right connector by squeezing it and pulling it away from the board.
Unplug the bottom right connector by squeezing it and pulling it away from the board.
Step 7
- Unplug the light connector by squeezing it and pulling away from the board.
Unplug the light connector by squeezing it and pulling away from the board.
Step 8
- Unplug the blue and white wires by squeezing the connector and pulling away from the board.
Unplug the blue and white wires by squeezing the connector and pulling away from the board.
Step 9
- Unplug the small white connector by squeezing it and pulling away from the board.
Unplug the small white connector by squeezing it and pulling away from the board.
Step 10
- Unplug the plug in the red connector.
- The red plug is glued to the board, so this step will require extra force.
Unplug the plug in the red connector.
The red plug is glued to the board, so this step will require extra force.
Step 11
- Unplug the charging cable connector by squeezing it and pulling it away from the board.
Unplug the charging cable connector by squeezing it and pulling it away from the board.
Step 12
- Cut the cable tie.
- Unplug the remaining wires.
- The connectors for the remaining wires are in the rubber covers.
Cut the cable tie.
Unplug the remaining wires.
The connectors for the remaining wires are in the rubber covers.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 4 other contributors
Jessica Ouyang
Member since: 10/08/2018
604 Reputation
4 Guides authored
Badges:
8
+5 more badges
Team
Cal Poly, Team S15-G4, White Fall 2018
Member of Cal Poly, Team S15-G4, White Fall 2018
CPSU-WHITE-F18S15G4
4 Members
10 Guides authored
Mark - Jun 6, 2020
Reply
I’ve got an active broken on the cover not the one to to speaker the other one. Does anyone know where is terminates. I can’t see where it came from. It can only reach the circuit board or the active of the speaker.
eden11 - Jan 1, 2021
Reply
Where do you buy the board?
