Hover 1 Titan Right Gyroscope Replacement Repair Guide

Difficulty

Moderate

Steps

10

Time Required

                          10 - 20 minutes            

Sections

2

• Bottom Right Panel
• 3 steps
• Right Gyroscope and Motherboard
• 7 steps

Flags

0

• BackHover-1 Titan

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              Bottom Right Panel               

• Flip the hoverboard so the bottom is facing up.
• The right side is the side that has the power button. There is also an “R” on the metal plate underneath the battery.

Flip the hoverboard so the bottom is facing up.

The right side is the side that has the power button. There is also an “R” on the metal plate underneath the battery.

1024

Step 2

• Using a Phillips #1 screwdriver, remove the two 14 mm screws closest to the center of the hoverboard.
• Using a Phillips #1 screwdriver, remove the four 12 mm screws located in the middle of the panel.
• Using a Phillips #1 screwdriver, remove the two 15 mm screws located closest to the wheel.

Using a Phillips #1 screwdriver, remove the two 14 mm screws closest to the center of the hoverboard.

Using a Phillips #1 screwdriver, remove the four 12 mm screws located in the middle of the panel.

Using a Phillips #1 screwdriver, remove the two 15 mm screws located closest to the wheel.

Step 3

• Grip the bottom right panel and lift to remove it.

Grip the bottom right panel and lift to remove it.

Step 4

              Right Gyroscope and Motherboard               

• Unplug the battery from the gyroscope/motherboard by holding the yellow connector and pulling apart.

Unplug the battery from the gyroscope/motherboard by holding the yellow connector and pulling apart.

Step 5

• Remove four 12 mm Phillips #1 head screws from the corners of the green gyroscope/motherboard.

Remove four 12 mm Phillips #1 head screws from the corners of the green gyroscope/motherboard.

Step 6

• Unplug the bottom left connector by squeezing it and pulling it away from the board.

Unplug the bottom left connector by squeezing it and pulling it away from the board.

Step 7

• Unplug the white wires by squeezing the connector and pulling away from the board.

Unplug the white wires by squeezing the connector and pulling away from the board.

Step 8

• Unplug one set of the red, white, purple, and black wires by squeezing the connector and pulling away from the board.

Unplug one set of the red, white, purple, and black wires by squeezing the connector and pulling away from the board.

Step 9

• Unplug the other set of the red, white, purple, and black wires by squeezing the connector and pulling away from the board.

Unplug the other set of the red, white, purple, and black wires by squeezing the connector and pulling away from the board.

Step 10

• Cut the cable tie and unplug the remaining wires.

Cut the cable tie and unplug the remaining wires.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.                                             

Author

                                      with 4 other contributors 

                    Jessica Ouyang                     

Member since: 10/08/2018

604 Reputation

                                      4 Guides authored                  



                       Badges:
                       8







                                                        +5 more badges                           

Team

                       Cal Poly, Team S15-G4, White Fall 2018                        

                                                  Member of Cal Poly, Team S15-G4, White Fall 2018 



                    CPSU-WHITE-F18S15G4                     


                                            4 Members                     


                                            10 Guides authored                     

jfsucher - Mar 28, 2020

Reply

Where can I get the circuit boards for the left and right ?