Difficulty

Moderate

Steps

17

Time Required

                          15 - 40 minutes

Sections

2

  • Bottom Left Panel
  • 3 steps
  • Wheel and Motor
  • 14 steps

Flags

0

  • BackHover-1 Titan

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Bottom Left Panel
  • Flip the hoverboard so the bottom is facing up.
  • The left side is the side that has the charge port. There is also an “L” on the metal plate underneath the wires.

Flip the hoverboard so the bottom is facing up.

The left side is the side that has the charge port. There is also an “L” on the metal plate underneath the wires.

1024

Step 2

  • Using a Phillips #1 screwdriver, remove the two 14 mm screws located closest to the center of the hoverboard.
  • Using a Phillips #1 screwdriver, remove the four 12 mm screws located in the middle of the panel.
  • Using a Phillips #1 screwdriver, remove two 15 mm screws located closest to the wheel.

Using a Phillips #1 screwdriver, remove the two 14 mm screws located closest to the center of the hoverboard.

Using a Phillips #1 screwdriver, remove the four 12 mm screws located in the middle of the panel.

Using a Phillips #1 screwdriver, remove two 15 mm screws located closest to the wheel.

Step 3

  • Grip the bottom left panel and lift up to remove.

Grip the bottom left panel and lift up to remove.

Step 4

              Wheel and Motor
  • Unplug the battery by pulling apart the yellow connectors.

Unplug the battery by pulling apart the yellow connectors.

Step 5

  • Use the Phillips #1 screwdriver to remove the four 12mm screws that attach the gyroscope/motherboard to the hoverboard.

Use the Phillips #1 screwdriver to remove the four 12mm screws that attach the gyroscope/motherboard to the hoverboard.

Step 6

  • Cut the rubber surrounding the yellow wire and pull the rubber apart, exposing the connectors.

Cut the rubber surrounding the yellow wire and pull the rubber apart, exposing the connectors.

Step 7

  • Unplug the yellow wires by gripping the wire close to the connectors and pulling apart.

Unplug the yellow wires by gripping the wire close to the connectors and pulling apart.

Step 8

  • Cut the rubber surrounding the green wire and pull the rubber apart, exposing the connectors.

Cut the rubber surrounding the green wire and pull the rubber apart, exposing the connectors.

Step 9

  • Unplug the green wires by gripping the wire close to the connectors and pulling apart.

Unplug the green wires by gripping the wire close to the connectors and pulling apart.

Step 10

  • Cut the rubber surrounding the blue wire and pull the rubber apart, exposing the connectors.

Cut the rubber surrounding the blue wire and pull the rubber apart, exposing the connectors.

Step 11

  • Unplug the blue wires by gripping the wire close to the connectors and pulling apart.

Unplug the blue wires by gripping the wire close to the connectors and pulling apart.

Step 12

  • Unplug the rainbow connector by squeezing the clips and pulling apart.

Unplug the rainbow connector by squeezing the clips and pulling apart.

Step 13

  • Use scissors to cut the zip tie around the group of wires.

Use scissors to cut the zip tie around the group of wires.

Step 14

  • Unplug the white wire connector by squeezing the clips and pulling apart.

Unplug the white wire connector by squeezing the clips and pulling apart.

Step 15

  • Use an impact driver with a hex 6 bit to loosen the four 20 mm hex 6 bolts.
  • Wear safety glasses while using the impact driver.

Use an impact driver with a hex 6 bit to loosen the four 20 mm hex 6 bolts.

Wear safety glasses while using the impact driver.

Step 16

  • Pull out the loosened screws with your hands and remove the metal plate.

Pull out the loosened screws with your hands and remove the metal plate.

Step 17

  • Lift the wheel and motor shaft up and out of the board.
  • The motor shaft is located within the wheel.

Lift the wheel and motor shaft up and out of the board.

The motor shaft is located within the wheel.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.

Author

                                      with 4 other contributors 


                    Emma Huun

Member since: 10/08/2018

303 Reputation

                                      1 Guide authored                  



                       Badges:
                       7







                                                        +4 more badges

Team

                       Cal Poly, Team S15-G4, White Fall 2018                        

                                                  Member of Cal Poly, Team S15-G4, White Fall 2018 



                    CPSU-WHITE-F18S15G4                     


                                            4 Members                     


                                            10 Guides authored