How To Bind Transmitter And Reciever Repair Guide

Difficulty

Easy

Steps

8

Time Required

                          5 minutes            

Sections

1

• How to Bind Transmitter and Reciever
• 8 steps

Flags

3

In Progress

This guide is a work in progress. Reload periodically to see the latest changes!

Needs More Images

A few more images would make this guide’s procedures crystal clear.

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

• BackBlade Nano QX

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              Disconnect the Battery               

• Disconnect the power cable and remove the battery

Disconnect the power cable and remove the battery

1024

Step 2

              Add a Model to the Transmitter               

• If using a transmitter other than the Blade MLP4DSM, add a new model to the transmitter.
• Select the appropriate model type.

If using a transmitter other than the Blade MLP4DSM, add a new model to the transmitter.

Select the appropriate model type.

Step 3

              Center Trims               

• Center all trims on the transmitter.
• If using the Blade MLP4DSM, press the trim buttons until you hear a long low beep (roll and pitch trim) or three short low beeps (throttle and yaw trim). This indicates that the trim is centered.

Center all trims on the transmitter.

If using the Blade MLP4DSM, press the trim buttons until you hear a long low beep (roll and pitch trim) or three short low beeps (throttle and yaw trim). This indicates that the trim is centered.

Step 4

              Power Off Transmitter               

• Turn the power off on the transmitter.
• Make sure the throttle is in the off position.
• If using a transmitter other than the Blade MLP4DSM, make sure that all switches are in the 0 position.

Turn the power off on the transmitter.

Make sure the throttle is in the off position.

If using a transmitter other than the Blade MLP4DSM, make sure that all switches are in the 0 position.

Step 5

              Reconnect the Battery               

• Reconnect the power cable to the battery.
• Make sure not to bend the pins on the connector.
• After 5 seconds, the status LED will turn blue and begin flashing rapidly, indicating that it has entered bind mode.

Reconnect the power cable to the battery.

Make sure not to bend the pins on the connector.

After 5 seconds, the status LED will turn blue and begin flashing rapidly, indicating that it has entered bind mode.

Step 6

              Enter Bind Mode on the Transmitter               

• Put the transmitter into bind mode while powering it on.
• If using the Blade MLP4DSM, push and hold the left stick while powering on the transmitter. Release the left stick. You will hear a beep and the power LED will blink.
• If using a different transmitter, consult the manual on how to enter bind mode.

Put the transmitter into bind mode while powering it on.

If using the Blade MLP4DSM, push and hold the left stick while powering on the transmitter. Release the left stick. You will hear a beep and the power LED will blink.

If using a different transmitter, consult the manual on how to enter bind mode.

Step 7

• The status LED will turn solid blue when it is successfully bound to the transmitter.

The status LED will turn solid blue when it is successfully bound to the transmitter.

Step 8

• Disconnect the battery from the power cable.
• Power off the transmitter.

Disconnect the battery from the power cable.

Power off the transmitter.

You should now be ready to fly your quadcopter.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.                                             

Author

                                      with 2 other contributors 

                    Ian Glen                     

Member since: 04/28/2014

291 Reputation

                                      3 Guides authored                  



                       Badges:
                       10







                                                        +7 more badges                           

jamiekif - Sep 4, 2019

Reply

That worked perfectly for me! And I used the MLP6 transmitter. Thanks kid! ;)

rob_swain - Jan 6, 2020

Reply

The drone is bound now but I cant get it to arm. Any suggestions? Not sure how to do it on this controller. Thank you!