Difficulty
Easy
Steps
13
Time Required
35 - 40 minutes
Sections
1
- How to Clean a PVC P-Trap
- 13 steps
Flags
0
BackPlumbing
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
The P-Trap is P shaped piping that directly follows the drain stopper and is usually located in the cabinets below a sink. The P-Trap is mainly intended to hold water in the bend with the intent of blocking foul smelling air from deeper within the plumbing of a house from coming out through the sink. It also serves the secondary purpose of catching small items dropped into the sink and allowing them to be retrieved.
Before beginning, ensure water to the sink being worked on is shut off and that your workspace is prepped for any potential spills.
What you need
Step 1
How to Clean a PVC P-Trap
- Clear out the space if the trap is located in a hard-to-reach place.
- Turn off the water valve for the sink.
Clear out the space if the trap is located in a hard-to-reach place.
Turn off the water valve for the sink.
1024
Step 2
- Place towels around the area.
- Place a bucket or bowl under the P-trap.
Place towels around the area.
Place a bucket or bowl under the P-trap.
Step 3
- Loosen the coupling nuts from the pipe above and below the drain using a wrench.
Loosen the coupling nuts from the pipe above and below the drain using a wrench.
Step 4
- Loosen the nuts on the upper and lower pipe and disconnect the the P-trap.
- Remove the U shape from the piping, and dump any water into bowl.
- Pull the PVC pipe that is connected to the wall out horizontally.
- Pull the PVC pipe closest to the drain in a downward motion.
Loosen the nuts on the upper and lower pipe and disconnect the the P-trap.
Remove the U shape from the piping, and dump any water into bowl.
Pull the PVC pipe that is connected to the wall out horizontally.
Pull the PVC pipe closest to the drain in a downward motion.
Step 5
- Empty any water into a bucket.
- Clear out the interior of the PVC pipe using a bottle brush or wire, spinning and moving the brush through the pipe.
- Remove any soap scum.
- This may appear black and sludge-like.
Empty any water into a bucket.
Clear out the interior of the PVC pipe using a bottle brush or wire, spinning and moving the brush through the pipe.
Remove any soap scum.
This may appear black and sludge-like.
Step 6
- Using a different water source, run the hot water through the P-trap parts.
- Check that the P-Trap parts are clear.
Using a different water source, run the hot water through the P-trap parts.
Check that the P-Trap parts are clear.
Step 7
- Reassemble the trap, but leave the horizontal pipe disconnected.
- Insert the short pipe into the the U shape and loosely tighten the nut.
Reassemble the trap, but leave the horizontal pipe disconnected.
Insert the short pipe into the the U shape and loosely tighten the nut.
Step 8
- Insert the horizontal pipe back into the water output in the wall. Begin to tighten the nut closest to the wall.
Insert the horizontal pipe back into the water output in the wall. Begin to tighten the nut closest to the wall.
Step 9
- Insert the top of the P-trap back onto drain pipe.
- Align the pipes so the pipes are touching.
- Once aligned, secure all the nuts tightly.
Insert the top of the P-trap back onto drain pipe.
Align the pipes so the pipes are touching.
Once aligned, secure all the nuts tightly.
Step 10
- Turn the water valve back on to check the P-Trap for leaks.
- Run hot water for 30 seconds or more, and use your hand to feel for any leaking.
- If you do, identify which section is leaking and tighten the nut.
- If it continues to leak, you may need to use threading tape, which is shown in the next step.
Turn the water valve back on to check the P-Trap for leaks.
Run hot water for 30 seconds or more, and use your hand to feel for any leaking.
If you do, identify which section is leaking and tighten the nut.
If it continues to leak, you may need to use threading tape, which is shown in the next step.
Step 11
- Take the P -trap off after locating the leak.
- Use the threading tape on the PVC pipe to help the nuts tighten. Simply wrap the threading tape around the threading on the pipe where the leak was found.
- Put the PVC P-trap back on and tighten the nuts.
- Turn the water back on as you check for leaks.
Take the P -trap off after locating the leak.
Use the threading tape on the PVC pipe to help the nuts tighten. Simply wrap the threading tape around the threading on the pipe where the leak was found.
Put the PVC P-trap back on and tighten the nuts.
Turn the water back on as you check for leaks.
Step 12
- wrap the tape in a clockwise direction around the pipe threads.
wrap the tape in a clockwise direction around the pipe threads.
Step 13
- Put the P trap back into place.
- Give the P-trap one more look to ensure all the nuts are tightened.
- Double check alignment and you are finished.
Put the P trap back into place.
Give the P-trap one more look to ensure all the nuts are tightened.
Double check alignment and you are finished.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 4 other contributors
Ashley m. Wuthrich -Hoffman
Member since: 11/17/2021
229 Reputation
1 Guide authored
Badges:
5
+2 more badges
Team
Idaho State University, Team 1-9, Watkins Fall 2021
Member of Idaho State University, Team 1-9, Watkins Fall 2021
ISU-WATKINS-F21S1G9
1 Member
1 Guide authored
