Difficulty

Difficult

Steps

12

Time Required

                          20 minutes            

Sections

2

  • Home Button Assembly
  • 6 steps
  • How to fix iPhone 6S/6S+ home button, when home button click does not work.
  • 6 steps

Flags

1

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

  • BackiPhone 6s Plus

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

Symptoms may include:

  • Only registers click occasionally.Only works when the home button bracket is not attached to the LCD.Only works if the button is held or twisted a certain way.Will not register click at all.

3U tools should still be able to recognize the home button, and Touch ID should still work. If they do not, this guide will not fix those problems.

What you need

Step 1

              Home Button Assembly               
  • Remove the two 1.9 mm Phillips screws securing the home button bracket.

Remove the two 1.9 mm Phillips screws securing the home button bracket.

1024

Step 2

  • Remove the home button bracket.

Remove the home button bracket.

Step 3

  • Use the pointed tip of a spudger to disconnect the home button cable from its connector on the display assembly.

Use the pointed tip of a spudger to disconnect the home button cable from its connector on the display assembly.

Step 4

  • The rubber gasket surrounding the home button is very thin and tears easily.
  • Apply mild heat (with an iOpener, heat gun, or hair dryer) to soften the adhesive securing the home button gasket.
  • Using your fingertip, gently press up on the home button from the front side of the display assembly. Use firm, constant pressure to slowly separate the home button’s rubber gasket from the front panel.

The rubber gasket surrounding the home button is very thin and tears easily.

Apply mild heat (with an iOpener, heat gun, or hair dryer) to soften the adhesive securing the home button gasket.

Using your fingertip, gently press up on the home button from the front side of the display assembly. Use firm, constant pressure to slowly separate the home button’s rubber gasket from the front panel.

Step 5

  • Use the pointed end of a spudger to pry the lightly-adhered home button flex cable off the display assembly.

Use the pointed end of a spudger to pry the lightly-adhered home button flex cable off the display assembly.

Step 6

  • Remove the home button assembly.

Remove the home button assembly.

Step 7

              Finding the Cause               
  • Though this step isn’t necessary, here are some images to help you see the cause of the issue
  • Here you can see the micro-tear that happens just under the edge of the home button.

Though this step isn’t necessary, here are some images to help you see the cause of the issue

Here you can see the micro-tear that happens just under the edge of the home button.

Step 8

              Locating the Component               
  • Find the resistor tied to the home button and remove the protective layer around that resistor.

Find the resistor tied to the home button and remove the protective layer around that resistor.

Step 9

              Verify the Issue               
  • Test continuity between top part of the resistor and the home button.
  • If you get constant continuity between these two points, you have another issue and this process will not fix your issue.

Test continuity between top part of the resistor and the home button.

If you get constant continuity between these two points, you have another issue and this process will not fix your issue.

Step 10

              Soldering (Part 1)               
  • Now that you have confirmed the issue, you can fix it by running an external trace between the two components you just tested.
  • Solder your wire to the physical part of the home button first.

Now that you have confirmed the issue, you can fix it by running an external trace between the two components you just tested.

Solder your wire to the physical part of the home button first.

Step 11

              Soldering (Part 2)               
  • Guide the wire to the second component
  • It is easier to keep the wire in place if you cut part of the glue out in a line. That way you can insert the wire into the cutout to prevent it from moving
  • Add some glue or UV resin to keep the wire in place.
  • Solder the wire to the top end of the component.

Guide the wire to the second component

It is easier to keep the wire in place if you cut part of the glue out in a line. That way you can insert the wire into the cutout to prevent it from moving

Add some glue or UV resin to keep the wire in place.

Solder the wire to the top end of the component.

Step 12

              Glue and Assemble               
  • Add some UV Curing Glue to the solder points.
  • To be safe, you can place some Kapton tape over the top of the new trace to keep it from moving. Be careful as this new trace is fragile where it isn’t glued.
  • Follow steps 1-6 in reverse order to re-assemble the device.

Add some UV Curing Glue to the solder points.

To be safe, you can place some Kapton tape over the top of the new trace to keep it from moving. Be careful as this new trace is fragile where it isn’t glued.

Follow steps 1-6 in reverse order to re-assemble the device.

After testing the home button and confirming that the repair worked, you can re-assemble your device.

Cancel: I did not complete this guide.

                                                                                      11 other people completed this guide.                                             

Author

                                      with 1 other contributor 

                    Jon                     

Member since: 08/17/2018

633 Reputation

                                      1 Guide authored                  



                       Badges:
                       10







                                                        +7 more badges                           

kumkrish36 - Jul 21, 2019

Reply

Superb it worked

Howard - Jul 3, 2020

Reply

Looks like have to attempt this. Have done fairly fine soldering before but maybe nothing this small. What size jumper to use? 0.1mm or 0.02mm?

Jon - Apr 22, 2021

Thanks Howard. Sorry I haven’t been around for a while. The wire I used was 0.02 mm. You would probably be fine with a thicker wire, this is just what I have on hand.

Howard - Jul 25, 2020

Reply

Great tutorial. There is a diagram floating around on the web that has the polarity reversed. I did that first and didn’t work before finding this guide and corrected the wiring. Works great now.

Besides a good fine tip soldering iron and at least magnifying goggles, really good flux makes all the difference on this job since everything is so small. I had some clear liquidy flux (Kester 951? don’t recall, bought long ago to help reflow GPU+SOC BGAs) That worked great as heat instantly flowed to all the right places. Necessary with tiny solder points and rework wire.