How To Open The Saeco Moltio Housing Plastic Frame Repair Guide

Difficulty

Moderate

Steps

Time Required

Suggest a time??

Sections

How to open the Saeco Moltio housing (plastic frame)
7 steps

Flags

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

BackSaeco Moltio
Full Screen
Options
History
Save to Favorites
Download PDF
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              How to open the Saeco Moltio housing (plastic frame)

First check which model you have in front of you: Is the decorative frame made of chromed metal (picture 1) or of metallized plastic? (picture 2). In the first case follow this guide, in the second case you are in the right place here.

First check which model you have in front of you: Is the decorative frame made of chromed metal (picture 1) or of metallized plastic? (picture 2). In the first case follow this guide, in the second case you are in the right place here.

1024

Step 2

Never forget to remove the power!
Remove the water reservoir, the brew unit, the milk reservoir, the lid for the bean storage and the drip tray.
Remove the lock on the bean storage container by pushing the button inwards.
Lift the bean storage container out.

Never forget to remove the power!

Remove the water reservoir, the brew unit, the milk reservoir, the lid for the bean storage and the drip tray.

Remove the lock on the bean storage container by pushing the button inwards.

Lift the bean storage container out.

Step 3

First, the metalized plastic decorative frame on the water tank side must be removed. It is only hold in place by clips, but it often jams so hard that you have to use a lot of force - but not so much that it breaks.
Lay the machine on its side so the bottom is facing you. Start using a metal tool at the bottom edge to pry off the trim. Use only plastic tools on the other edges to avoid damaging the frame. The notches gradually release with a loud crack.
Lift off the frame.

First, the metalized plastic decorative frame on the water tank side must be removed. It is only hold in place by clips, but it often jams so hard that you have to use a lot of force - but not so much that it breaks.

Lay the machine on its side so the bottom is facing you. Start using a metal tool at the bottom edge to pry off the trim. Use only plastic tools on the other edges to avoid damaging the frame. The notches gradually release with a loud crack.

Lift off the frame.

Step 4

Now start dismantling the top panel. First remove the two Torx T10 screws at the top of the back.
Remove the four Torx T10 screws from under the bean container.

Now start dismantling the top panel. First remove the two Torx T10 screws at the top of the back.

Remove the four Torx T10 screws from under the bean container.

Step 5

Using a plastic pry tool gently disengage the top panel and lift it up and out. It might jam a little, especially under the decorative frame on the side with the service flap.
When assembling, make sure that the slide for unlocking the bean container engages correctly in the mechanism.

Using a plastic pry tool gently disengage the top panel and lift it up and out. It might jam a little, especially under the decorative frame on the side with the service flap.

When assembling, make sure that the slide for unlocking the bean container engages correctly in the mechanism.

Step 6

Now the side part on the water tank side can be removed. It is still attached with three screws.
The first Torx T10 screw is in the top rear corner, the second is in the middle of the upper edge . Twist them out.
Remove the Torx T10 screw on the left under the slot for the water tank.

Now the side part on the water tank side can be removed. It is still attached with three screws.

The first Torx T10 screw is in the top rear corner, the second is in the middle of the upper edge . Twist them out.

Remove the Torx T10 screw on the left under the slot for the water tank.

Step 7

Lay the machine on its side. Now you can lift off the side panel. There is a small notch in the top right and it is probably still a bit stuck.
In principle, the side with the service flap could also be removed in a similar way, but this is not necessary for many repairs.
Picture 2 shows the Moltio with side panel open:
pump
flowmeter
PCB
heater

Lay the machine on its side. Now you can lift off the side panel. There is a small notch in the top right and it is probably still a bit stuck.

In principle, the side with the service flap could also be removed in a similar way, but this is not necessary for many repairs.

Picture 2 shows the Moltio with side panel open:

pump

flowmeter

PCB

heater

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      8 other people completed this guide.                                             


        VauWeh is helping us fix the world!      Want to contribute?      Start translating ›

Special thanks to these translators:

100%

VauWeh

Author

                                      with 1 other contributor

                    VauWeh

Member since: 10/19/2015

160,518 Reputation

                                      211 Guides authored                  



                       Badges:
                       41







                                                        +38 more badges

Peter Nohner - Apr 7, 2022

Super Bilderklärung mit den farbigen Hinweisen.

So und nicht anders ist es richtig erklärt.

Ansgar - May 28, 2022

Sehr hilfreich! Danke

Member-Contributed Guide#

Introduction#

What you need#

Member-Contributed Guide

Introduction

What you need