Difficulty
Moderate
Steps
9
Time Required
20 - 30 minutes
Sections
1
- How to Reassemble the Palm IIIc
- 9 steps
Flags
2
Needs Better Images
Better photos will improve this guide. Help out by taking, editing, or uploading new ones!
Better Introduction
Improve this guide by completing or revising its introduction.
BackPalm IIIc
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
What you need
Step 1
How to Reassemble the Palm IIIc
- Reinsert the screen into the case that contains the buttons.
Reinsert the screen into the case that contains the buttons.
1024
Step 2
- Put the Motherboard back into casing from right to left.
- Make sure the black clips are securing the motherboard into the casing.
Put the Motherboard back into casing from right to left.
Make sure the black clips are securing the motherboard into the casing.
Step 3
- Secure the bottom two ZIF connectors into their slots by opening the flap and inserting the ZIF connectors.
- Gently press down on the flap to secure the ZIF connector. This secures the screen and buttons to the motherboard.
Secure the bottom two ZIF connectors into their slots by opening the flap and inserting the ZIF connectors.
Gently press down on the flap to secure the ZIF connector. This secures the screen and buttons to the motherboard.
Step 4
- Connect the blue and red screen cables to the beige box they were removed from.
Connect the blue and red screen cables to the beige box they were removed from.
Step 5
- Open the ZIF connector box at the top of the motherboard by gently pulling up on the flap.
- Insert the ZIF tab into the connector box.
- Gently press down on the flap to secure the ZIF tab in place.
Open the ZIF connector box at the top of the motherboard by gently pulling up on the flap.
Insert the ZIF tab into the connector box.
Gently press down on the flap to secure the ZIF tab in place.
Step 6
- Attach the white box on the end of the red cable connected to the battery into the connector box on the motherboard.
Attach the white box on the end of the red cable connected to the battery into the connector box on the motherboard.
Step 7
- Place the front and back covers around the casing containing the motherboard and screen.
- Before securing the covers, place the sensor in between the front and back cover at the top of the device.
- After the sensor is in place between the two covers, firmly secure the front and back covers.
Place the front and back covers around the casing containing the motherboard and screen.
Before securing the covers, place the sensor in between the front and back cover at the top of the device.
After the sensor is in place between the two covers, firmly secure the front and back covers.
Step 8
- Replace the long screws at the top of the back case with the Philips head screwdriver.
- Replace the short screws to the bottom of the back case using the Philips head screwdriver.
- After the screws are in place, insert the stylus.
Replace the long screws at the top of the back case with the Philips head screwdriver.
Replace the short screws to the bottom of the back case using the Philips head screwdriver.
After the screws are in place, insert the stylus.
Step 9
- Gently snap the flip cover back into place where it connects at the top of the Palm IIIc
Gently snap the flip cover back into place where it connects at the top of the Palm IIIc
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 3 other contributors
Angela Arthur
Member since: 02/16/2012
101 Reputation
1 Guide authored
Badges:
3
Team
Ohio State, Team 1-5, Buehl Winter 2012
Member of Ohio State, Team 1-5, Buehl Winter 2012
OSU-BUEHL-W12S1G5
5 Members
1 Guide authored