How To Remove Carbon Buildup In A 2012 Volkswagon Cc Repair Guide

Difficulty

Easy

Steps

Time Required

                          15 - 20 minutes

Sections

How to Remove Carbon Buildup In A 2012 Volkswagon CC
12 steps

Flags

Back2012 Volkswagen CC
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              How to Remove Carbon Buildup In A 2012 Volkswagon CC

Start the engine.
Let the engine warm up to operating temperature.
Shut the engine off.

Start the engine.

Let the engine warm up to operating temperature.

Shut the engine off.

1024

Step 2

Locate the hood latch lever under the left side of the dash on the driver side of the vehicle.
Pull the hood latch lever towards the rear of the vehicle to unlock the hood.
Apply upward pressure on the front of the hood and pull up on the plastic lever that is under the front center section of the hood.

Locate the hood latch lever under the left side of the dash on the driver side of the vehicle.

Pull the hood latch lever towards the rear of the vehicle to unlock the hood.

Apply upward pressure on the front of the hood and pull up on the plastic lever that is under the front center section of the hood.

Step 3

Find the engine air intake hose near the top rear of the engine bay.
The opening clip can be found near the joint of the intake hose.
Make sure this clip is located after the Mass Airflow Sensor in order to avoid a check engine light.
The engine may be hot to the touch.

Find the engine air intake hose near the top rear of the engine bay.

The opening clip can be found near the joint of the intake hose.

Make sure this clip is located after the Mass Airflow Sensor in order to avoid a check engine light.

The engine may be hot to the touch.

Step 4

Hang the intake cleaner can in the engine bay for easy access and use in the future steps.
Remove the line from the packaging.

Hang the intake cleaner can in the engine bay for easy access and use in the future steps.

Remove the line from the packaging.

Step 5

Apply pressure on the tabs of the metal clip with the pliers to release the pressure from the intake hose.
Slide the clip to the left so that it does not cover the joint.
The clip is very strong, so a large amount of force may be required.

Apply pressure on the tabs of the metal clip with the pliers to release the pressure from the intake hose.

Slide the clip to the left so that it does not cover the joint.

The clip is very strong, so a large amount of force may be required.

Step 6

Separate the hose connection by applying a twisting and pulling force simultaneously on both ends of the connection.

Separate the hose connection by applying a twisting and pulling force simultaneously on both ends of the connection.

Step 7

Insert the metal hook at the end of the valve cleaner line into hose opening.
Close the intake hose over the hook being sure not to pinch the part of the line that is not covered by the hook.
Secure the intake hose so that a moderately tight seal keeps the valve cleaner line secure.

Insert the metal hook at the end of the valve cleaner line into hose opening.

Close the intake hose over the hook being sure not to pinch the part of the line that is not covered by the hook.

Secure the intake hose so that a moderately tight seal keeps the valve cleaner line secure.

Step 8

Guide the extra cleaner line through the metal hook so that it extends into the intake hose.

Guide the extra cleaner line through the metal hook so that it extends into the intake hose.

Step 9

Turn the red dial for the cleaner timer from the “O” to the “I” position.

Turn the red dial for the cleaner timer from the “O” to the “I” position.

Step 10

This step will start the timer on the can. You will have 1 minute before the can starts dispensing the cleaner. Be ready to complete step 11 and start step 12 in this time frame.
Arm the spring in the can by turning the blue dial from “O” to “I".
Assure the can is secure so that it will not interfere with the engine or fall off the hanger.

This step will start the timer on the can. You will have 1 minute before the can starts dispensing the cleaner. Be ready to complete step 11 and start step 12 in this time frame.

Arm the spring in the can by turning the blue dial from “O” to “I".

Assure the can is secure so that it will not interfere with the engine or fall off the hanger.

Step 11

Return to the interior of the vehicle.
Assure the vehicle is in neutral and the parking brake is set to prevent inadvertent vehicle movement.
Start the vehicle within one minute of arming the valve cleaner can.

Return to the interior of the vehicle.

Assure the vehicle is in neutral and the parking brake is set to prevent inadvertent vehicle movement.

Start the vehicle within one minute of arming the valve cleaner can.

Step 12

Press the accelerator and bring the engine up to 3x idle speed.
For this make and model the speed will read 2800 RPM.
Hold the engine at this speed for 9-10 minutes until the cleaner is completely empty.
Shut off the engine.

Press the accelerator and bring the engine up to 3x idle speed.

For this make and model the speed will read 2800 RPM.

Hold the engine at this speed for 9-10 minutes until the cleaner is completely empty.

Shut off the engine.

To reassemble your vehicle, follow these instructions from step 6 to step 2 in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 3 other contributors

                    Raphael Shoshani

Member since: 01/23/2020

235 Reputation

                                      1 Guide authored                  



                       Badges:
                       4







                                                        +1 more badge

Team

                       Embry-Riddle Aeronautical University, Team S19-G1, Ives Spring 2020                        

                                                  Member of Embry-Riddle Aeronautical University, Team S19-G1, Ives Spring 2020 



                    ERAU-IVES-S20S19G1                     


                                            3 Members                     


                                            1 Guide authored

Introduction#

What you need#

Team#

Introduction

What you need

Team