How To Repair Hoses For 4 Function Diamond Microdermabrasion Unit Sly 08Xlt Nv 07D Vacuum System Repair Guide

Difficulty

Moderate

Steps

6

Time Required

                          10 minutes            

Sections

1

• How to repair hoses for 4 Function Diamond Microdermabrasion Unit SLY-08XLT. NV-07D Vacuum System
• 6 steps

Flags

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

• Back4 Function Diamond Microdermabrasion Unit SLY-08XLT. NV-07D

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

What you need

Step 1

              How to repair hoses for 4 Function Diamond Microdermabrasion Unit SLY-08XLT. NV-07D Vacuum System               

• Disconnect all of the wand attachments from the unit.

Disconnect all of the wand attachments from the unit.

1024

Step 2

• Remove all of the clear plastic holders. There are a total of seven screws to remove, and three plastic holders.

Remove all of the clear plastic holders. There are a total of seven screws to remove, and three plastic holders.

Step 3

• Flip the unit on it’s face, with a soft towel under it. Remove ten screws, all on the outer edge of the bottom of the unit. To keep screws together, and with the correct piece of the unit, try to use scotch or masking tape them on a strip of tape and tape them directly to the portion that you removed

Flip the unit on it’s face, with a soft towel under it. Remove ten screws, all on the outer edge of the bottom of the unit. To keep screws together, and with the correct piece of the unit, try to use scotch or masking tape them on a strip of tape and tape them directly to the portion that you removed

Step 4

• Gently pull the bottom, with its back facing up, outward and down to the floor, as to not disturb the connected wires, which are not long enough to pull straight downward.

Gently pull the bottom, with its back facing up, outward and down to the floor, as to not disturb the connected wires, which are not long enough to pull straight downward.

Step 5

• Look over all of the hoses, their connections and the filters inside each end to make sure there are no holes, cracks or kinks in them. Make certain that the hoses are tightly connected to each port and there is not a leak. Inspect the filters for clogs, too much dust or tears.
• Replace any bad hoses or connections. If the end of each hose is bad, simply cut the tip of it off and put it back on it’s port. Throw away dirty or clogged filters, and replace them with new ones. To be safe, use either electrical or duct tape around the filter housing of each, to prevent air leaks or separation of the housing.

Look over all of the hoses, their connections and the filters inside each end to make sure there are no holes, cracks or kinks in them. Make certain that the hoses are tightly connected to each port and there is not a leak. Inspect the filters for clogs, too much dust or tears.

Replace any bad hoses or connections. If the end of each hose is bad, simply cut the tip of it off and put it back on it’s port. Throw away dirty or clogged filters, and replace them with new ones. To be safe, use either electrical or duct tape around the filter housing of each, to prevent air leaks or separation of the housing.

Step 6

• Check the interior for any debris or dust blocking the fan and fan motor and simply remove it or clean it out. Check for loose wires, bad connections or wires that are damaged.

Check the interior for any debris or dust blocking the fan and fan motor and simply remove it or clean it out. Check for loose wires, bad connections or wires that are damaged.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      4 other people completed this guide.                                             

Author

                                      with 3 other contributors 

                    Pam                     

Member since: 02/25/2013

183 Reputation

                                      1 Guide authored                  



                       Badges:
                       11







                                                        +8 more badges                           

Kristina Jurisic - Dec 7, 2015

Reply

Hello, can you please tell me where can I buy parts for this machine? I have it allready 7 years and I´m very happy with it, but my skin scrubber (handpeace) doesn´t work any more. thank you, Kristina

Pam - Mar 12, 2016

Kristina…..i have been sick… Sorry for the delay in answering. I’ll have to look up the information, but most of the parts are generic pieces. Depending on what you need to order… It could be as easy ead going to a hardware store. Let me know what parts you’re looking for and I’ll see if I can find them.

elinaaronin - Jan 2, 2017

Reply

If anyone knows where it’s can be rapair it in NY area

Andy Gregorio - Nov 5, 2019

Reply

My microdermabrasion has not .. Function the air of the machine is thru away ..

ccountrycottage - Apr 16, 2020

Reply

I am getting ready to set up my machine, do you have a better manual that show you in picture form of each item and how it works. There is one piece I have no idea how to use it , it looks like a small wand. It would be nice to show how the to insert rings and filters in a picture form.

Thank you

Sissy. 04-16-2020