How To Replace Bearings In A Quantum Bill Dance Edition Bait Casting Reel Repair Guide

Difficulty

Moderate

Steps

Time Required

                          30 - 35 minutes

Sections

Bearings
15 steps

Flags

Inconsistent Images

Updating the images on this guide to be more consistent with the prerequisites would increase its awesomeness.

Needs Better Images

Better photos will improve this guide. Help out by taking, editing, or uploading new ones!

Better Introduction

Improve this guide by completing or revising its introduction.

Missing Details

Some of this guide’s details are missing. Help users by adding tools, difficulty, or time.

BackFishing Tackle
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Bearings

Use the Phillips #1 screwdriver to remove three screws.

Use the Phillips #1 screwdriver to remove three screws.

1024

Step 2

Use a flathead screwdriver to remove the screw.
After removing the screw, remove the black cap on top of the handle of the reel.

Use a flathead screwdriver to remove the screw.

After removing the screw, remove the black cap on top of the handle of the reel.

Step 3

Use a 10 mm socket wrench to remove the nut.

Use a 10 mm socket wrench to remove the nut.

Step 4

With the nut now removed, remove the handle of the reel. You may need to gently wiggle it out of place if it will not remove.

With the nut now removed, remove the handle of the reel. You may need to gently wiggle it out of place if it will not remove.

Step 5

Remove this washer gently, You may also need to wiggle this piece out of place if it is stuck.

Remove this washer gently, You may also need to wiggle this piece out of place if it is stuck.

Step 6

Twist the drag dial off in order to remove it.

Twist the drag dial off in order to remove it.

Step 7

Under the removed drag dial should be 4 metal washers. Simply pull them off the gold bolt.

Under the removed drag dial should be 4 metal washers. Simply pull them off the gold bolt.

Step 8

Use a Phillips #0 screwdriver to remove the two screws.

Use a Phillips #0 screwdriver to remove the two screws.

Step 9

After removing the two screws, remove the handle sides side plate of the reel. You may need to wiggle it off in order to remove it.

After removing the two screws, remove the handle sides side plate of the reel. You may need to wiggle it off in order to remove it.

Step 10

With the side plate removed, take out the existing washer. It should be easy, but if not wiggle it free.

With the side plate removed, take out the existing washer. It should be easy, but if not wiggle it free.

Step 11

Now flip to the break side of the reel. This is the opposite side of the handle.
Push this button and twist upward in order to remove the side plate. Remember to push and twist simultaneously.

Now flip to the break side of the reel. This is the opposite side of the handle.

Push this button and twist upward in order to remove the side plate. Remember to push and twist simultaneously.

Step 12

Remove the spool. It may take a little wiggle in order for it to line up with the casing around it and come out.

Remove the spool. It may take a little wiggle in order for it to line up with the casing around it and come out.

Step 13

Use a pair of pliers to remove the pin. There should be a big and small side of the pin. Remove the pin pushing from the smaller side in order to not strip the casing it sits in. It may take a little force, but try to be as gentle as possible.
After removing the pin pull out the bearing and replace it with a new one.

Use a pair of pliers to remove the pin. There should be a big and small side of the pin. Remove the pin pushing from the smaller side in order to not strip the casing it sits in. It may take a little force, but try to be as gentle as possible.

After removing the pin pull out the bearing and replace it with a new one.

Step 14

Use a small flathead screwdriver to put tension on the spring and remove it. Remember to be very delicate removing the spring in order to not break or bend the spring.

Use a small flathead screwdriver to put tension on the spring and remove it. Remember to be very delicate removing the spring in order to not break or bend the spring.

Step 15

With the spring removed, remove the bearing and replace it with a new bearing.

With the spring removed, remove the bearing and replace it with a new bearing.

To reassemble your device, follow these instructions in reverse order. Remember to take your time, be very delicate, and be sure to assemble the device with all of the required pieces in order.

Cancel: I did not complete this guide.

Author

                                      with 1 other contributor

                    David S

Member since: 03/20/2021

241 Reputation

                                      1 Guide authored                  



                       Badges:
                       5







                                                        +2 more badges

Team

                       Grand Valley State University, Team S3-G8, DeVasto Winter 2021                        

                                                  Member of Grand Valley State University, Team S3-G8, DeVasto Winter 2021 



                    GVSU-DEVASTO-W21S3G8                     


                                            1 Member                     


                                            1 Guide authored

Inconsistent Images#

Needs Better Images#

Better Introduction#

Missing Details#

Introduction#

What you need#

Team#