Difficulty
Moderate
Steps
8
Time Required
15 - 30 minutes
Sections
1
- Circuit Board
- 8 steps
Flags
0
BackCyclone Range Hood (Model CY3000R)
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
All of the range hood’s components, including the fans, LED lights, and control panel, receive electricity from the circuit board. The range hood could occasionally go faulty owing to a power problem with the circuit board.
Please locate your fuse box before using the guide so you can turn off the electricity and prevent any unexpected electric shocks.
What you need
Step 1
Circuit Board
- To avoid unforeseen electric shocks, turn off the fuse supplying power to your range hood to avoid the risk of electrocution.
- Empty all of the grease from the grease container and clean it.
To avoid unforeseen electric shocks, turn off the fuse supplying power to your range hood to avoid the risk of electrocution.
Empty all of the grease from the grease container and clean it.
1024
Step 2
- The panel will be loose after the screws and bulbs are removed; be sure to support the panel while removing the screws and bulbs.
- Remove the five 10 mm Phillips #1 screws securing the panel while holding the panel in place.
The panel will be loose after the screws and bulbs are removed; be sure to support the panel while removing the screws and bulbs.
Remove the five 10 mm Phillips #1 screws securing the panel while holding the panel in place.
Step 3
- Turn the LED bulbs counterclockwise and remove them.
- Push the panel down to remove it from the body.
Turn the LED bulbs counterclockwise and remove them.
Push the panel down to remove it from the body.
Step 4
- Carefully remove the four 5 mm Phillips #1 screws from the board box.
- Open the lid.
Carefully remove the four 5 mm Phillips #1 screws from the board box.
Open the lid.
Step 5
- Pull out the ten-pin white head cable located on the left side of the board.
- Remove the cables one by one on the right side of the board.
- Install the replacement board into the board box.
Pull out the ten-pin white head cable located on the left side of the board.
Remove the cables one by one on the right side of the board.
Install the replacement board into the board box.
Step 6
- Insert the tips of the wires into the board’s protective plastic that comes with your replacement board.
- To reinsert the wires, insert the two black wires into the first two slots on the top.
- The second row is for the white wires, which can be attached in any order; for the remaining red wires, adhere to the ordered numbers attached to the wires.
Insert the tips of the wires into the board’s protective plastic that comes with your replacement board.
To reinsert the wires, insert the two black wires into the first two slots on the top.
The second row is for the white wires, which can be attached in any order; for the remaining red wires, adhere to the ordered numbers attached to the wires.
Step 7
- Replace the lid.
- Reinstall the four 5 mm Phillips #1 screws to secure the lid.
- Shut the panel.
Replace the lid.
Reinstall the four 5 mm Phillips #1 screws to secure the lid.
Shut the panel.
Step 8
- Set the panel in place, and secure all five 10 mm Phillips #1 screws to their respective locations while holding the panel.
- Replace the LED bulbs.
Set the panel in place, and secure all five 10 mm Phillips #1 screws to their respective locations while holding the panel.
Replace the LED bulbs.
Enjoy your fully functional range.
Cancel: I did not complete this guide.
Author
with 1 other contributor
Hesam Esmaeilianaraghi
Member since: 07/06/2022
157 Reputation
1 Guide authored
Badges:
2
Team
York University, Team M-7, Allen Summer 2022
Member of York University, Team M-7, Allen Summer 2022
YORK-ALLEN-SU22SMG7
1 Member
1 Guide authored
