Difficulty

Moderate

Steps

12

Time Required

                          20 - 30 minutes

Sections

4

  • Back Cover
  • 5 steps
  • Fan
  • 3 steps
  • Heat Sink
  • 1 step
  • Speakers
  • 3 steps

Flags

0

  • BackHP 14-fq1025nr

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Back Cover
  • Flip the laptop upside down so the bottom cover is facing up.

Flip the laptop upside down so the bottom cover is facing up.

1024

Step 2

  • Use a pair of tweezers to grab and pull the feet off of the cover.

Use a pair of tweezers to grab and pull the feet off of the cover.

Step 3

  • Remove the two 4 mm screws using a Phillips #0 screwdriver.
  • Remove the six remaining 6 mm screws located around the edges and underneath the feet using a Phillips #0 screwdriver.

Remove the two 4 mm screws using a Phillips #0 screwdriver.

Remove the six remaining 6 mm screws located around the edges and underneath the feet using a Phillips #0 screwdriver.

Step 4

  • Flip the laptop right-side up and slide an iFixit opening tool and/or Jimmy inside of the bottom cover seam to pry it open.

Flip the laptop right-side up and slide an iFixit opening tool and/or Jimmy inside of the bottom cover seam to pry it open.

Step 5

  • Remove the bottom cover.

Remove the bottom cover.

Step 6

              Fan
  • Remove the three silver screws (one 2 mm screw and two 4 mm screws) holding down the fan using a Phillips #0 screwdriver.

Remove the three silver screws (one 2 mm screw and two 4 mm screws) holding down the fan using a Phillips #0 screwdriver.

Step 7

  • Unplug the fan’s power cord from the motherboard.
  • Use tweezers to pull the plug out, if needed.

Unplug the fan’s power cord from the motherboard.

Use tweezers to pull the plug out, if needed.

Step 8

  • Remove the fan.

Remove the fan.

Step 9

              Heat Sink
  • Remove the four gray 3 mm screws around the heat sink using a Phillips #0 screwdriver.
  • Remove the heat sink.

Remove the four gray 3 mm screws around the heat sink using a Phillips #0 screwdriver.

Remove the heat sink.

Step 10

              Speakers
  • Using a Phillips #0 screwdriver, remove the three black 5 mm screws holding down the speaker:
  • Two screws on the left side
  • One screw on the right side

Using a Phillips #0 screwdriver, remove the three black 5 mm screws holding down the speaker:

Two screws on the left side

One screw on the right side

Step 11

  • Unplug the speaker wire.
  • Use tweezers if needed.

Unplug the speaker wire.

Use tweezers if needed.

Step 12

  • Remove the speaker.

Remove the speaker.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors 


                    Nil Parra

Member since: 09/27/2022

485 Reputation

                                      4 Guides authored                  



                       Badges:
                       7







                                                        +4 more badges

Team

                       Utah Tech University, Team 1-6, McMurrin Fall 2022                        

                                                  Member of Utah Tech University, Team 1-6, McMurrin Fall 2022 



                    UTAHTECH-MCMURRIN-F22S1G6                     


                                            3 Members                     


                                            9 Guides authored