Difficulty

Moderate

Steps

11

Time Required

                          30 minutes

Sections

3

  • Battery
  • 2 steps
  • Back Panel
  • 5 steps
  • Display Screen Hinges
  • 4 steps

Flags

1

Better Introduction

Improve this guide by completing or revising its introduction.

  • BackHP 15-ay103dx

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

What you need

Step 1

              Battery
  • Slide the two battery lock latches on the back of the device to the “unlock” position.

Slide the two battery lock latches on the back of the device to the “unlock” position.

1024

Step 2

  • Lift the battery upward to remove it from the device.

Lift the battery upward to remove it from the device.

Step 3

              Back Panel
  • Using the PH1 phillips-head screwdriver, remove all the 5/16 in. screws from the back of the device.
  • There should be 10 in total, be sure to keep them together!

Using the PH1 phillips-head screwdriver, remove all the 5/16 in. screws from the back of the device.

There should be 10 in total, be sure to keep them together!

Step 4

  • Locate the optical disc drive and remove it from the device by sliding it straight of the device.

Locate the optical disc drive and remove it from the device by sliding it straight of the device.

Step 5

  • Covering the hinges of the device are rubber bumpers secured to the device using adhesive. Remove them carefully.
  • Place the adhesive side up as you will need to place them back after your replacement is complete.

Covering the hinges of the device are rubber bumpers secured to the device using adhesive. Remove them carefully.

Place the adhesive side up as you will need to place them back after your replacement is complete.

Step 6

  • In the same spot you’ve just removed the bumpers from, you will find two 5/16 in. screws. Using the same Phillips-head screwdriver used in step 2, remove the screws
  • Be sure to keep the screws together!

In the same spot you’ve just removed the bumpers from, you will find two 5/16 in. screws. Using the same Phillips-head screwdriver used in step 2, remove the screws

Be sure to keep the screws together!

Step 7

  • Carefully remove the back panel from the device.
  • If you are unable to do this with your hands, you can use a thin prying tool of your choice to make it easier!

Carefully remove the back panel from the device.

If you are unable to do this with your hands, you can use a thin prying tool of your choice to make it easier!

Step 8

              Display Screen Hinges
  • Use a spudger to carefully remove the border around the display screen.
  • As long as you are slow and delicate, the border will eventually come off.

Use a spudger to carefully remove the border around the display screen.

As long as you are slow and delicate, the border will eventually come off.

Step 9

  • Remove the two 5/16 screws in the top corners and the four in the bottom corners.

Remove the two 5/16 screws in the top corners and the four in the bottom corners.

Step 10

  • Carefully pull the screen from the hinges and lower it on to the table.
  • There will be wires running from the screen to the motherboard. You do not need to unplug these.
  • The hinges are made of malleable metal and are easily bent.

Carefully pull the screen from the hinges and lower it on to the table.

There will be wires running from the screen to the motherboard. You do not need to unplug these.

The hinges are made of malleable metal and are easily bent.

Step 11

  • Remove the 5/16 screws securing the hinges to the computer.

Remove the 5/16 screws securing the hinges to the computer.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 2 other contributors 


                    Kody Franklin

Member since: 09/25/2017

131 Reputation

                                      1 Guide authored                  



                       Badges:
                       6







                                                        +3 more badges

Team

                       University of North Texas, Team S3-G3, Thompson Fall 2017                        

                                                  Member of University of North Texas, Team S3-G3, Thompson Fall 2017 



                    UNT-THOMPSON-F17S3G3                     


                                            4 Members                     


                                            6 Guides authored