Hp 15 D076Nr Motherboard Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          1 hour

Sections

Battery
4 steps
Wireless Card
6 steps
Motherboard
17 steps

Flags

BackHP 15-d076nr
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

Orient the laptop upside down so that the back of the laptop, where the battery is located, faces you.
Locate the left and right switches at the bottom of the laptop.

Orient the laptop upside down so that the back of the laptop, where the battery is located, faces you.

Locate the left and right switches at the bottom of the laptop.

1024

Step 2

Move the right switch to the left so that the orange unlock symbol is showing.

Move the right switch to the left so that the orange unlock symbol is showing.

Step 3

Move the left switch to the right, covering the battery symbol, and hold.

Move the left switch to the right, covering the battery symbol, and hold.

Step 4

While holding the left switch in place, slide the battery towards you and away from the laptop.

While holding the left switch in place, slide the battery towards you and away from the laptop.

Step 5

              Wireless Card

Re-orient the laptop, so that the back of the laptop faces away from you.

Re-orient the laptop, so that the back of the laptop faces away from you.

Step 6

Locate the small screw on the panel at the center of the laptop.
Loosen the small screw using a Philips # 1 screwdriver.
The screw does not come free from the panel. It only needs to be loosened enough so that the panel can be lifted/pried.

Locate the small screw on the panel at the center of the laptop.

Loosen the small screw using a Philips # 1 screwdriver.

The screw does not come free from the panel. It only needs to be loosened enough so that the panel can be lifted/pried.

Step 7

Carefully pry the middle panel up using a plastic spudger, or other prying tool .
Pull the panel away from the laptop and set it off to the side.

Carefully pry the middle panel up using a plastic spudger, or other prying tool .

Pull the panel away from the laptop and set it off to the side.

Step 8

Gently wiggle and lift the black antenna wire away from the wireless card.
If there is also a white wire attached, both black and white wires will need to be removed from the wireless card.

Gently wiggle and lift the black antenna wire away from the wireless card.

If there is also a white wire attached, both black and white wires will need to be removed from the wireless card.

Step 9

Locate the Phillips 2.0x3.0mm screw on the upper left corner of the wireless card.
Carefully remove the 2.0x3.0mm screw using a Philips #0 screwdriver.

Locate the Phillips 2.0x3.0mm screw on the upper left corner of the wireless card.

Carefully remove the 2.0x3.0mm screw using a Philips #0 screwdriver.

Step 10

Slide the wireless card to the left to remove it from the socket.

Slide the wireless card to the left to remove it from the socket.

Step 11

              Motherboard

Locate the RAM in the exposed area.

Locate the RAM in the exposed area.

Step 12

Locate the latches on the RAM.
Slide the latches away from the RAM using a plastic spudger.
The RAM might spring out.

Locate the latches on the RAM.

Slide the latches away from the RAM using a plastic spudger.

The RAM might spring out.

Step 13

Remove the RAM.

Remove the RAM.

Step 14

Locate the ribbon cables.
Pry up the black tabs on the connectors and disconnect both of the ribbon cables.

Locate the ribbon cables.

Pry up the black tabs on the connectors and disconnect both of the ribbon cables.

Step 15

Locate the DVD drive screw.
Remove the Phillips PM2.5×6.5 screw using a Phillips #0 screwdriver.
Continue using a Phillips #0 screwdriver for the rest of this guide, and subsequent guides.
Take the screw and place it in a container so as to not lose it.

Locate the DVD drive screw.

Remove the Phillips PM2.5×6.5 screw using a Phillips #0 screwdriver.

Continue using a Phillips #0 screwdriver for the rest of this guide, and subsequent guides.

Take the screw and place it in a container so as to not lose it.

Step 16

Push down the tab that is located by the DVD drive screw.
Take the DVD drive in one hand, and using the plastic spludger, push the tab down, and out.

Push down the tab that is located by the DVD drive screw.

Take the DVD drive in one hand, and using the plastic spludger, push the tab down, and out.

Step 17

Remove the fourteen Phillips PM2.5×6.0 screws, and place them in a separate container.

Remove the fourteen Phillips PM2.5×6.0 screws, and place them in a separate container.

Step 18

Flip the laptop over, and open it as if you were using it.
Gently, remove the laptop cover/keyboard from the laptop using the plastic spudger.
When you remove the cover/keyboard, the laptop will become top heavy.

Flip the laptop over, and open it as if you were using it.

Gently, remove the laptop cover/keyboard from the laptop using the plastic spudger.

When you remove the cover/keyboard, the laptop will become top heavy.

Step 19

Disconnect the monitor cable, using the plastic spudger, and pry it upwards.
Pull the cable from its routing until it is free.

Disconnect the monitor cable, using the plastic spudger, and pry it upwards.

Pull the cable from its routing until it is free.

Step 20

Lift the black tabs, and disconnect the three ribbon cables.
Disconnect the red-black-white speaker cable located in the lower left corner.

Lift the black tabs, and disconnect the three ribbon cables.

Disconnect the red-black-white speaker cable located in the lower left corner.

Step 21

Remove the three Phillips PM2.5×4.0 screws on the card reader in the bottom left corner.
Place the screws in a separate container.
Remove the card reader.

Remove the three Phillips PM2.5×4.0 screws on the card reader in the bottom left corner.

Place the screws in a separate container.

Remove the card reader.

Step 22

Remove the five Phillips PM2.5×5.0 screws on the motherboard.

Remove the five Phillips PM2.5×5.0 screws on the motherboard.

Step 23

Remove the Phillips PM2.5×5.0 screw located on the fan, in the upper right corner.

Remove the Phillips PM2.5×5.0 screw located on the fan, in the upper right corner.

Step 24

Carefully lift up the motherboard.
Do not completely remove the motherboard. Simply lift it. There is a black cable on the bottom of the motherboard that is anchoring it.

Carefully lift up the motherboard.

Do not completely remove the motherboard. Simply lift it. There is a black cable on the bottom of the motherboard that is anchoring it.

Step 25

Locate the cable on the underside of the motherboard, in its lower right corner.
Carefully grip the cable, and pull downward to remove it.

Locate the cable on the underside of the motherboard, in its lower right corner.

Carefully grip the cable, and pull downward to remove it.

Step 26

Flip the motherboard over.

Flip the motherboard over.

Step 27

Locate the charge port cable connection point on the motherboard.
Grab the charge port cable’s connector, and wiggle it to remove it.
Set the board off to the side.

Locate the charge port cable connection point on the motherboard.

Grab the charge port cable’s connector, and wiggle it to remove it.

Set the board off to the side.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.

Author

                                      with 3 other contributors

                    Amy Weed

Member since: 01/12/2017

577 Reputation

                                      5 Guides authored                  



                       Badges:
                       9







                                                        +6 more badges

Team

                       Oakland University, Team 2-2, Ruskiewicz Winter 2017                        

                                                  Member of Oakland University, Team 2-2, Ruskiewicz Winter 2017 



                    OAK-RUSKIEWICZ-W17S2G2                     


                                            4 Members                     


                                            7 Guides authored

Question??? - Mar 31, 2022

H! May I have the part number of the LCD flex cable? or can you send me a picture of it? Thanks.

Introduction#

What you need#

Team#

Introduction

What you need

Team