Difficulty
Difficult
Steps
15
Time Required
40 minutes
Sections
5
- Front Panel Assembly
- 4 steps
- Keyboard
- 2 steps
- CD Drive
- 1 step
- Cooling Fan
- 3 steps
- Screen
- 5 steps
Flags
0
BackHP 15-r137wm TouchSmart
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Front Panel Assembly
- Make sure that the device is powered off and unplugged before removing components.
- Remove all ten (10) 5.5 mm Phillips #0 screws.
- Remove the two (2) plastic tabs located at the rear of the panel. Locate the two (2) 7.5mm Phillips #0 screws underneath the pads and remove.
Make sure that the device is powered off and unplugged before removing components.
Remove all ten (10) 5.5 mm Phillips #0 screws.
Remove the two (2) plastic tabs located at the rear of the panel. Locate the two (2) 7.5mm Phillips #0 screws underneath the pads and remove.
1024
Step 2
- Use a wide plastic opening tool to pry off the top casing.
- Be cautious not to crack the casing near the keyboard as it is quite fragile.
- Lift the cover off carefully as there are wires still attached to internal components.
- After panel is removed, use an anti-static wrist strap to ensure the motherboard does not get any external shocks from static discharge.
Use a wide plastic opening tool to pry off the top casing.
Be cautious not to crack the casing near the keyboard as it is quite fragile.
Lift the cover off carefully as there are wires still attached to internal components.
After panel is removed, use an anti-static wrist strap to ensure the motherboard does not get any external shocks from static discharge.
Step 3
- The connection for the track pad is still connected.
- Move the keyboard slightly out of the way to locate the connection.
- Disconnect the small wire protruding from the motherboard underneath the metal plate.
The connection for the track pad is still connected.
Move the keyboard slightly out of the way to locate the connection.
Disconnect the small wire protruding from the motherboard underneath the metal plate.
Step 4
- Locate the connection between the power button and the connecting cable.
- Do not lift the front panel off to far as the cable is still attached.
- Remove the cable from the motherboard carefully.
Locate the connection between the power button and the connecting cable.
Do not lift the front panel off to far as the cable is still attached.
Remove the cable from the motherboard carefully.
Step 5
Keyboard
- Disconnect the connection between the keyboard the the motherboard.
Disconnect the connection between the keyboard the the motherboard.
Step 6
- Remove the four (4) 2.5mm by 3.5mm Phillips #0 screws from the metal retaining plate.
- Lift the metal retaining plate off and away from the device.
Remove the four (4) 2.5mm by 3.5mm Phillips #0 screws from the metal retaining plate.
Lift the metal retaining plate off and away from the device.
Step 7
CD Drive
- Slide the CD drive out slowly by pulling it to the right. There are no screws attached, but there is a connection to the motherboard.
Slide the CD drive out slowly by pulling it to the right. There are no screws attached, but there is a connection to the motherboard.
Step 8
Cooling Fan
- Locate the small connection on the motherboard and disconnect it by slowly pulling it away from the motherboard.
- Slowly disconnect the cable as the wires are very small and fragile
Locate the small connection on the motherboard and disconnect it by slowly pulling it away from the motherboard.
Slowly disconnect the cable as the wires are very small and fragile
Step 9
- Remove the three (3) 2.5mm by 3.5mm Phillips #0 screws from the fan.
Remove the three (3) 2.5mm by 3.5mm Phillips #0 screws from the fan.
Step 10
- Remove the cooling fan from the housing carefully.
- The fan may be connected to the small foam screen. Pull gently to release it.
Remove the cooling fan from the housing carefully.
The fan may be connected to the small foam screen. Pull gently to release it.
Step 11
Screen
- Remove the 5.5mm Phillips #0 screw.
Remove the 5.5mm Phillips #0 screw.
Step 12
- Gently pull and slide the video card out of its connector.
Gently pull and slide the video card out of its connector.
Step 13
- Lift up tape, and then remove the power cable from its connector.
Lift up tape, and then remove the power cable from its connector.
Step 14
- Remove all four (4) 5.5mm Phillips #0 screws.
- Remove the one (1) 2.5mm Phillips #0 screw.
- Since all of the screws are now removed, the screen will begin to fall off on its own. make sure the screen is supported before removal.
Remove all four (4) 5.5mm Phillips #0 screws.
Remove the one (1) 2.5mm Phillips #0 screw.
Since all of the screws are now removed, the screen will begin to fall off on its own. make sure the screen is supported before removal.
Step 15
- The screen can now be lifted out of place from the laptop.
The screen can now be lifted out of place from the laptop.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 2 other contributors
Ross B Jacques
Member since: 10/18/2017
857 Reputation
7 Guides authored
Badges:
10
+7 more badges
Team
UMass Dartmouth, Team S4-G4, Julie Fall 2017
Member of UMass Dartmouth, Team S4-G4, Julie Fall 2017
UMASSD-JULIE-F17S4G4
3 Members
7 Guides authored
