Difficulty
Easy
Steps
7
Time Required
10 - 15 minutes
Sections
2
- Back Cover
- 3 steps
- Front and Rear Facing Cameras
- 4 steps
Flags
0
BackHP 7 Plus 1302
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
*In order to access the camera, please refer to the HP 7 Plus 1302 Back Cover Removal Guide
Back Cover Removal Guide
Relevant Parts
Camera
What you need
Step 1
Back Cover
- Using the T5 Torx Screwdriver, remove the T5x3mm screws located in all 4 corners.
- Device should be turned off and unplugged before starting the replacements.
Using the T5 Torx Screwdriver, remove the T5x3mm screws located in all 4 corners.
Device should be turned off and unplugged before starting the replacements.
1024
Step 2
- Use the plastic opening tool to push in between the front and the back of the tablet.
- Slide the plastic opening tool around all 4 sides of the tablet to separate the back cover.
- Be careful when you are trying to remove the back as it can damage the screen if you force it too much.
Use the plastic opening tool to push in between the front and the back of the tablet.
Slide the plastic opening tool around all 4 sides of the tablet to separate the back cover.
Be careful when you are trying to remove the back as it can damage the screen if you force it too much.
Step 3
- Continue sliding the plastic opening tool around the tablet until all 4 sides are separated from each other.
- Remove the back cover.
Continue sliding the plastic opening tool around the tablet until all 4 sides are separated from each other.
Remove the back cover.
Step 4
Front and Rear Facing Cameras
- The cameras are connected together via a small ribbon cable with one electrical connection in between them.
- Locate the small grey connector near the top of the device. Using the Spudger tool, gently pull it away from the device until it releases its connection.
- This will come out very easily so don’t use much force.
The cameras are connected together via a small ribbon cable with one electrical connection in between them.
Locate the small grey connector near the top of the device. Using the Spudger tool, gently pull it away from the device until it releases its connection.
This will come out very easily so don’t use much force.
Step 5
- Next move to front facing camera. Using the plastic spudger, push the small tabs out of the way while lightly pulling up on the camera.
- There is a tab on either side of the camera that must both be released.
- Then gently pull the camera up and away from the device.
Next move to front facing camera. Using the plastic spudger, push the small tabs out of the way while lightly pulling up on the camera.
There is a tab on either side of the camera that must both be released.
Then gently pull the camera up and away from the device.
Step 6
- The rear facing camera is held down with double sided tape.
- Using the tweezers, gently pry the rear facing camera up out of its socket.
The rear facing camera is held down with double sided tape.
Using the tweezers, gently pry the rear facing camera up out of its socket.
Step 7
- Lift the camera assembly away from the device to remove it.
Lift the camera assembly away from the device to remove it.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 3 other contributors
Erik Hegg
Member since: 07/09/2015
224 Reputation
1 Guide authored
Badges:
7
+4 more badges
Team
IUPUI, Team 1-2, Renguette SU 2015
Member of IUPUI, Team 1-2, Renguette SU 2015
IUPUI-RENGUETTE-SU15S1G2
5 Members
8 Guides authored
