Difficulty

Difficult

Steps

15

Time Required

                          25 minutes

Sections

4

  • Back Cover
  • 3 steps
  • Battery
  • 2 steps
  • Motherboard
  • 9 steps
  • Headphone Jack
  • 1 step

Flags

3

Action Shots

Be an action hero! This guide needs images that better demonstrate how to perform specific actions.

Incorrect Tools

Help make this guide better by using the correct tools in images and/or text.

Needs Better Images

Better photos will improve this guide. Help out by taking, editing, or uploading new ones!

  • BackHP 7 Plus 1302

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Back Cover
  • Using the T5 Torx Screwdriver, remove the T5x3mm screws located in all 4 corners.
  • Device should be turned off and unplugged before starting the replacements.

Using the T5 Torx Screwdriver, remove the T5x3mm screws located in all 4 corners.

Device should be turned off and unplugged before starting the replacements.

1024

Step 2

  • Use the plastic opening tool to push in between the front and the back of the tablet.
  • Slide the plastic opening tool around all 4 sides of the tablet to separate the back cover.
  • Be careful when you are trying to remove the back as it can damage the screen if you force it too much.

Use the plastic opening tool to push in between the front and the back of the tablet.

Slide the plastic opening tool around all 4 sides of the tablet to separate the back cover.

Be careful when you are trying to remove the back as it can damage the screen if you force it too much.

Step 3

  • Continue sliding the plastic opening tool around the tablet until all 4 sides are separated from each other.
  • Remove the back cover.

Continue sliding the plastic opening tool around the tablet until all 4 sides are separated from each other.

Remove the back cover.

Step 4

              Battery
  • Push out the battery connector using the spudger.
  • Swing the battery connector clear of the connector socket.

Push out the battery connector using the spudger.

Swing the battery connector clear of the connector socket.

Step 5

  • Lift the battery from the device.

Lift the battery from the device.

Step 6

              Motherboard
  • Pry the connector that attaches the front and back camera with a metal spudger.

Pry the connector that attaches the front and back camera with a metal spudger.

Step 7

  • Pull the camera from the connectors.

Pull the camera from the connectors.

Step 8

  • Identify the three T5x1mm screws and remove them with a Phillips #000

Identify the three T5x1mm screws and remove them with a Phillips #000

Step 9

  • Unplug the connector with the tweezers.
  • Remove the tape.

Unplug the connector with the tweezers.

Remove the tape.

Step 10

  • Flip the ZIF connector with the metal spudger.
  • Pull the ribbon connector out.

Flip the ZIF connector with the metal spudger.

Pull the ribbon connector out.

Step 11

  • Pull the orange tape with the tweezers.
  • Flip the ZIF connector with the spudger.
  • Pull the ribbon connector with the tweezers.

Pull the orange tape with the tweezers.

Flip the ZIF connector with the spudger.

Pull the ribbon connector with the tweezers.

Step 12

  • Remove the gray tape below the ribbon connector.

Remove the gray tape below the ribbon connector.

Step 13

  • Flip the ZIF connector.
  • Pull the ribbon connector out with the tweezers.

Flip the ZIF connector.

Pull the ribbon connector out with the tweezers.

Step 14

  • Pull the circuit board off.

Pull the circuit board off.

Step 15

              Headphone Jack
  • Desolder the six points on the headphone jack using the soldering iron.
  • Soldering iron will be hot be careful.
  • For more instructions about how to use the Soldering iron click here.

Desolder the six points on the headphone jack using the soldering iron.

Soldering iron will be hot be careful.

For more instructions about how to use the Soldering iron click here.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors 


                    Shannon Suttles

Member since: 01/29/2017

225 Reputation

                                      2 Guides authored                  



                       Badges:
                       6







                                                        +3 more badges

Team

                       IUPUI, Team 1-4, Baechle Spring 2017                        

                                                  Member of IUPUI, Team 1-4, Baechle Spring 2017 



                    IUPUI-BAECHLE-S17S1G4                     


                                            4 Members                     


                                            8 Guides authored