Difficulty

Moderate

Steps

10

Time Required

                          7 minutes

Sections

2

  • Keyboard Mount
  • 5 steps
  • Display Assembly
  • 5 steps

Flags

0

  • BackHP Chromebook 11 G3

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Keyboard Mount
  • Flip the laptop upside down so that the lid lies flat on the table.
  • Remove the nine 6mm Phillips #00 screws that line the border.

Flip the laptop upside down so that the lid lies flat on the table.

Remove the nine 6mm Phillips #00 screws that line the border.

1024

Step 2

  • Remove the two rubber feet closest to the hinge using tweezers.
  • Remove the two 6mm Phillips #00 screws revealed under these rubber feet.
  • The rubber feet may tear while removal; preventing this can be difficult, but it won’t harm the laptop. If desired, replace these rubber feet during reassembly.

Remove the two rubber feet closest to the hinge using tweezers.

Remove the two 6mm Phillips #00 screws revealed under these rubber feet.

The rubber feet may tear while removal; preventing this can be difficult, but it won’t harm the laptop. If desired, replace these rubber feet during reassembly.

Step 3

  • Flip the laptop so it is in the upright position.
  • Open the lid.
  • Unsnap the keyboard mount along the border of the laptop using a plastic opening tool.
  • This may require more force than expected. Hearing loud clicks as the plastic opening tool slides along the seam is normal.

Flip the laptop so it is in the upright position.

Open the lid.

Unsnap the keyboard mount along the border of the laptop using a plastic opening tool.

This may require more force than expected. Hearing loud clicks as the plastic opening tool slides along the seam is normal.

Step 4

  • Tilt the keyboard mount up.
  • Use a spudger to flip up the two ZIF connector retaining flaps for the ribbon cables that connect the keyboard mount to the motherboard.
  • Gently remove both ribbon cables.

Tilt the keyboard mount up.

Use a spudger to flip up the two ZIF connector retaining flaps for the ribbon cables that connect the keyboard mount to the motherboard.

Gently remove both ribbon cables.

Step 5

  • Lift the keyboard mount out of the laptop.

Lift the keyboard mount out of the laptop.

Step 6

              Display Assembly
  • Gently tug on the black and white wires connected to the Wi-Fi module to disconnect them.

Gently tug on the black and white wires connected to the Wi-Fi module to disconnect them.

Step 7

  • Using a spudger, lift the ZIF retaining flap that secures the display’s ribbon cable to the motherboard.
  • Gently pull the ribbon cable out of its socket.

Using a spudger, lift the ZIF retaining flap that secures the display’s ribbon cable to the motherboard.

Gently pull the ribbon cable out of its socket.

Step 8

  • Free the wire from the casing.

Free the wire from the casing.

Step 9

  • Remove the two 6mm Phillips #00 screws located near the upper left and right corners of the hinge mounts.
  • Hold the lid so that it is folded slightly inwards while removing the screws so that the lid doesn’t fall.

Remove the two 6mm Phillips #00 screws located near the upper left and right corners of the hinge mounts.

Hold the lid so that it is folded slightly inwards while removing the screws so that the lid doesn’t fall.

Step 10

  • Rotate the lid to a 90-degree angle with the table.
  • Shimmy the lid out of the laptop.

Rotate the lid to a 90-degree angle with the table.

Shimmy the lid out of the laptop.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 4 other contributors 


                    Rahul Goyal

Member since: 04/26/2017

1,369 Reputation

                                      10 Guides authored                  



                       Badges:
                       11







                                                        +8 more badges

Team

                       Cal Poly, Team S23-G3, Livingston Spring 2017                        

                                                  Member of Cal Poly, Team S23-G3, Livingston Spring 2017 



                    CPSU-LIVINGSTON-S17S23G3                     


                                            4 Members                     


                                            12 Guides authored