Difficulty

Moderate

Steps

13

Time Required

Suggest a time??

Sections

2

  • Printer Cover
  • 8 steps
  • Control Panel
  • 5 steps

Flags

0

  • BackHP Deskjet 3000 j310a

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Disconnect Printer
  • Begin to disassemble the printer by disconnecting from all power sources and computers. Keep cords separate and allow the printer to cool for 5 minutes.

Begin to disassemble the printer by disconnecting from all power sources and computers. Keep cords separate and allow the printer to cool for 5 minutes.

1024

Step 2

              Remove Bottom Cover
  • Flip the printer upside down and locate the cover on the left hand side. It is rectangular shape and is held in place by two screws. Unscrew these screws and take off cover.

Flip the printer upside down and locate the cover on the left hand side. It is rectangular shape and is held in place by two screws. Unscrew these screws and take off cover.

Step 3

              Release Paper Output Tray
  • To release the tray from the printer, you must manually pull it out. Hold the tray and push towards one side of the printer. Then pull away from the printer towards the other side. Keep output tray separate.

To release the tray from the printer, you must manually pull it out. Hold the tray and push towards one side of the printer. Then pull away from the printer towards the other side. Keep output tray separate.

Step 4

              Unscrew Cover
  • Turn the printer upside down. Locate the four screws holding the cover in place. These will be on the edges of the cover.

Turn the printer upside down. Locate the four screws holding the cover in place. These will be on the edges of the cover.

Step 5

  • Unscrew the four screws, keeping them separate. Turn the printer back right side up

Unscrew the four screws, keeping them separate. Turn the printer back right side up

Step 6

              Pull Off Top
  • Place fingers on the edge of the red cover. Begin to pull upwards to release the top portion, working your way around the printer. Make sure that it does not fall back into place.

Place fingers on the edge of the red cover. Begin to pull upwards to release the top portion, working your way around the printer. Make sure that it does not fall back into place.

Step 7

              Disconnect Cover
  • Once the top is loose, there will still be a connection wire between the printer and the cover. This wire will be about one inch wide and white, located under the buttons.

Once the top is loose, there will still be a connection wire between the printer and the cover. This wire will be about one inch wide and white, located under the buttons.

Step 8

  • Detach the wire from the printer by pulling the blue-sealed end from the white holder.

Detach the wire from the printer by pulling the blue-sealed end from the white holder.

Step 9

              Control Panel
  • Now that the top cover is removed from the printer body you will need to separate the control panel from the maroon panel.

Now that the top cover is removed from the printer body you will need to separate the control panel from the maroon panel.

Step 10

  • The control panel is connected to the maroon panel by four plastic hooks (two are seen in the picture and the other two are opposite them). Using a plastic opening tool pry each hook out of its locked position.

The control panel is connected to the maroon panel by four plastic hooks (two are seen in the picture and the other two are opposite them). Using a plastic opening tool pry each hook out of its locked position.

Step 11

  • You will need to remove the button, button circuit board, and screen in order to replace the control panel.

You will need to remove the button, button circuit board, and screen in order to replace the control panel.

Step 12

  • Unscrew the three screws indicated in the image. Unplug the connection from the screen, lift up the board, and remove from the panel. Pull the button out.

Unscrew the three screws indicated in the image. Unplug the connection from the screen, lift up the board, and remove from the panel. Pull the button out.

Step 13

  • Using the plastic opening tool pry the black tabs back and lift the screen out of the control panel.

Using the plastic opening tool pry the black tabs back and lift the screen out of the control panel.

Using the new control panel follow all steps in reverse to reassemble your printer.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors 


                    Lee

Member since: 10/17/2014

201 Reputation

                                      2 Guides authored                  



                       Badges:
                       4







                                                        +1 more badge

Team

                       UMass Dartmouth, Team 1-5, Duarte Fall 2014                        

                                                  Member of UMass Dartmouth, Team 1-5, Duarte Fall 2014 



                    UMASSD-DUARTE-F14S1G5                     


                                            3 Members                     


                                            7 Guides authored