Hp Deskjet F4480 Mother Board Replacement Repair Guide

Difficulty

Moderate

Steps

9

Time Required

                          15 minutes            

Sections

3

• Open front access panel
• 1 step
• Removing Top Lid
• 4 steps
• Mother Board
• 4 steps

Flags

Markup Mishap

This guide needs better markups. Help out by correcting or making some markup annotations.

Needs More Images

A few more images would make this guide’s procedures crystal clear.

Step Trimmer

This guide has unnecessary steps. Trim them to be more concise!

• BackHP Deskjet F4480

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              Open front access panel               

• Open the front access panel by placing your finger in the front slot and pulling gently.

Open the front access panel by placing your finger in the front slot and pulling gently.

1024

Step 2

              Removing Top Lid               

• Open the protective lid that is covering the glass. Press gently against the base of the panel to remove the lid from the rest of the printer.

Open the protective lid that is covering the glass. Press gently against the base of the panel to remove the lid from the rest of the printer.

Step 3

• Remove the four 9mm T10 Torx screws on the top.

Remove the four 9mm T10 Torx screws on the top.

Step 4

• Carefully lift the top panel off of the printer.
• Do not tear or damage the two cables that connect the top lid to the motherboard.

Carefully lift the top panel off of the printer.

Do not tear or damage the two cables that connect the top lid to the motherboard.

Step 5

• Remove the two cables by gripping each one close to their connection ports on the motherboard and gently disconnecting them.

Remove the two cables by gripping each one close to their connection ports on the motherboard and gently disconnecting them.

Step 6

              Mother Board               

• The mother board is located at the back of the printer.

The mother board is located at the back of the printer.

Step 7

• Take note of the wire’s location and orientation as this will be important to properly reassemble your device.
• Remove all of the wires connected to the mother board. There are seven in total.

Take note of the wire’s location and orientation as this will be important to properly reassemble your device.

Remove all of the wires connected to the mother board. There are seven in total.

Step 8

• Remove the three 9mm T10 Torx screws that hold the motherboard to the body of the printer

Remove the three 9mm T10 Torx screws that hold the motherboard to the body of the printer

Step 9

• At this point, the mother board should be free of all connections from the rest of the printer.
• Remove and replace the mother board with the new one.

At this point, the mother board should be free of all connections from the rest of the printer.

Remove and replace the mother board with the new one.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      7 other people completed this guide.                                             

Author

                                      with 5 other contributors 

                    Allen Bailey                     

Member since: 01/15/2013

218 Reputation

                                      1 Guide authored                  



                       Badges:
                       7







                                                        +4 more badges                           

Team

                       Cal Poly, Team 18-35, Regan Winter 2013                        

                                                  Member of Cal Poly, Team 18-35, Regan Winter 2013 



                    CPSU-REGAN-W13S18G35                     


                                            5 Members                     


                                            8 Guides authored                     

Ken Craven - Jun 2, 2017

Reply

ok so ineed to replace the Motherboard – where do I get this board and what is the cost?

viateur levesque - Jan 5, 2021

Reply

ou est localiser le sensor encoder module cb781-8006 merci

ou est installer le sensor encoder CB781-8006 Merci