Difficulty
Moderate
Steps
12
Time Required
30 minutes
Sections
2
- Screen
- 6 steps
- Front Webcam
- 6 steps
Flags
0
BackHP Elite x2 1012 G2
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Screen
- Make sure the device is turned off before starting.
- Orient the device so the back is facing you, with the kickstand up.
Make sure the device is turned off before starting.
Orient the device so the back is facing you, with the kickstand up.
1024
Step 2
- Remove the six 3mm Torx T5 screws underneath the kickstand.
Remove the six 3mm Torx T5 screws underneath the kickstand.
Step 3
- Turn the device over so the screen is facing you.
- Place a suction cup firmly onto a corner of the screen.
- Lift up gently until you see the screen separate from the casing.
- Repeat this process for all four corners.
Turn the device over so the screen is facing you.
Place a suction cup firmly onto a corner of the screen.
Lift up gently until you see the screen separate from the casing.
Repeat this process for all four corners.
Step 4
- Lift the screen up and off of the device.
- Pry each corner up first, otherwise you may damage or crack the screen.
Lift the screen up and off of the device.
Pry each corner up first, otherwise you may damage or crack the screen.
Step 5
- Remove the two connectors on the back of the screen by lifting the connector tabs on the motherboard with a plastic opening tool and pulling gently.
Remove the two connectors on the back of the screen by lifting the connector tabs on the motherboard with a plastic opening tool and pulling gently.
Step 6
- Remove the screen by gently lifting it off of the device.
Remove the screen by gently lifting it off of the device.
Step 7
Front Webcam
- Orient the device so that the battery is closest to you.
- The battery is the large, black rectangle at the bottom of the device.
Orient the device so that the battery is closest to you.
The battery is the large, black rectangle at the bottom of the device.
Step 8
- Remove the wire connector to the front webcam using a plastic opening tool. Hook the tool underneath the connector and pull up and back.
Remove the wire connector to the front webcam using a plastic opening tool. Hook the tool underneath the connector and pull up and back.
Step 9
- Remove the connector immediately to the left of the front webcam’s connector. Use a plastic opening tool to gently lift the connector up and out.
Remove the connector immediately to the left of the front webcam’s connector. Use a plastic opening tool to gently lift the connector up and out.
Step 10
- Remove the connector immediately to the right of the front webcam’s connector. Use a plastic opening tool to gently lift the connector up and out.
Remove the connector immediately to the right of the front webcam’s connector. Use a plastic opening tool to gently lift the connector up and out.
Step 11
- Use a Phillips screwdriver to remove the Phillips M2.0x2.0 screw to the left of the webcam. Turn the screwdriver counterclockwise to remove the screw.
Use a Phillips screwdriver to remove the Phillips M2.0x2.0 screw to the left of the webcam. Turn the screwdriver counterclockwise to remove the screw.
Step 12
- Remove the webcam using a plastic opening tool to lift it up and off.
Remove the webcam using a plastic opening tool to lift it up and off.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 2 other contributors
Noah Stapp
Member since: 04/18/2018
668 Reputation
2 Guides authored
Badges:
11
+8 more badges
Team
Cal Poly, Team S18-G5, Livingston Spring 2018
Member of Cal Poly, Team S18-G5, Livingston Spring 2018
CPSU-LIVINGSTON-S18S18G5
4 Members
13 Guides authored
