Difficulty

Moderate

Steps

9

Time Required

                          20 minutes

Sections

2

  • Screen
  • 6 steps
  • SSD
  • 3 steps

Flags

0

  • BackHP Elite x2 1012 G2

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Screen
  • Make sure the device is turned off before starting.
  • Orient the device so the back is facing you, with the kickstand up.

Make sure the device is turned off before starting.

Orient the device so the back is facing you, with the kickstand up.

1024

Step 2

  • Remove the six 3mm Torx T5 screws underneath the kickstand.

Remove the six 3mm Torx T5 screws underneath the kickstand.

Step 3

  • Turn the device over so the screen is facing you.
  • Place a suction cup firmly onto a corner of the screen.
  • Lift up gently until you see the screen separate from the casing.
  • Repeat this process for all four corners.

Turn the device over so the screen is facing you.

Place a suction cup firmly onto a corner of the screen.

Lift up gently until you see the screen separate from the casing.

Repeat this process for all four corners.

Step 4

  • Lift the screen up and off of the device.
  • Pry each corner up first, otherwise you may damage or crack the screen.

Lift the screen up and off of the device.

Pry each corner up first, otherwise you may damage or crack the screen.

Step 5

  • Remove the two connectors on the back of the screen by lifting the connector tabs on the motherboard with a plastic opening tool and pulling gently.

Remove the two connectors on the back of the screen by lifting the connector tabs on the motherboard with a plastic opening tool and pulling gently.

Step 6

  • Remove the screen by gently lifting it off of the device.

Remove the screen by gently lifting it off of the device.

Step 7

              SSD
  • Orient the device so that the battery is closest to you.
  • The battery is the large, black rectangle at the bottom of the device.

Orient the device so that the battery is closest to you.

The battery is the large, black rectangle at the bottom of the device.

Step 8

  • Remove the single Phillips M2.0x2.0 screw on the SSD using a Phillips screwdriver. Turn the screwdriver counterclockwise to remove the screw.

Remove the single Phillips M2.0x2.0 screw on the SSD using a Phillips screwdriver. Turn the screwdriver counterclockwise to remove the screw.

Step 9

  • Gently pull the SSD to the left and up to remove it from the device.

Gently pull the SSD to the left and up to remove it from the device.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      10 other people completed this guide.

Author

                                      with 4 other contributors 


                    Hunter Lane

Member since: 04/18/2018

247 Reputation

                                      1 Guide authored                  



                       Badges:
                       8







                                                        +5 more badges

Team

                       Cal Poly, Team S18-G5, Livingston Spring 2018                        

                                                  Member of Cal Poly, Team S18-G5, Livingston Spring 2018 



                    CPSU-LIVINGSTON-S18S18G5                     


                                            4 Members                     


                                            13 Guides authored

Andreas Gerl - Nov 16, 2019

Reply

Vielen Dank für die sehr gute Anleitung. Es hat alles perfekt geklappt.

Das Display selber sitzt zum Teil aber sehr fest im Gehäuse und man muss sich überwinden etwas Kraft anzuwenden.

Sollte man zu fest ziehen (und einem das Display entgegenspringt) besteht ja die Gefahr die filigranen Kabel abzureißen.