Hp Elite X2 1013 G3 Fingerprint Scanner Replacement Repair Guide

Difficulty

Easy

Steps

Time Required

                          30 minutes

Sections

Screen
4 steps
Battery
2 steps
Fingerprint Scanner
5 steps

Flags

BackHP Elite X2 1013 G3
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Screen

Flip the device over so the base is facing the ceiling.
Lift up the tablet stand.
Remove the four 2 mm screws from the tablet using a T5 Torx screwdriver.

Flip the device over so the base is facing the ceiling.

Lift up the tablet stand.

Remove the four 2 mm screws from the tablet using a T5 Torx screwdriver.

1024

Step 2

Flip the tablet over with the screen facing upwards.
Place the suction handle in the center of the screen and slowly lift off the screen until it is at a 30 degree angle, starting by gently prying up the bottom.
Do not pull the screen beyond a 30 degree angle. Additional internal components must be disconnected first.

Flip the tablet over with the screen facing upwards.

Place the suction handle in the center of the screen and slowly lift off the screen until it is at a 30 degree angle, starting by gently prying up the bottom.

Do not pull the screen beyond a 30 degree angle. Additional internal components must be disconnected first.

Step 3

With the screen lifted at a 30 degree angle, gently disconnect the yellow ribbon cable at the end connected to the screen.
Gently disconnect the orange ribbon cable at the end connected to the bottom plate.

With the screen lifted at a 30 degree angle, gently disconnect the yellow ribbon cable at the end connected to the screen.

Gently disconnect the orange ribbon cable at the end connected to the bottom plate.

Step 4

Remove the screen from the tablet.

Remove the screen from the tablet.

Step 5

              Battery

Use the Phillips #00 screwdriver to remove the six 2 mm screws.
Gently disconnect the two connectors.

Use the Phillips #00 screwdriver to remove the six 2 mm screws.

Gently disconnect the two connectors.

Step 6

Lift the battery out of the housing.

Lift the battery out of the housing.

Step 7

              Fingerprint Scanner

Disconnect the connector from the motherboard with your fingers.
The screwdriver is only used as a pointing device. Never attempt to use a screwdriver to pry components apart.

Disconnect the connector from the motherboard with your fingers.

The screwdriver is only used as a pointing device. Never attempt to use a screwdriver to pry components apart.

Step 8

Remove the two speaker/antenna module mounting 2mm screws using a Phillips #00 Screwdriver.

Remove the two speaker/antenna module mounting 2mm screws using a Phillips #00 Screwdriver.

Step 9

Use a spudger to gently pry the left black plastic speaker/antenna module off of the frame as pictured. Start by lifting up the right side of the module, then slowly work your way down the module towards the right.
The slight cracking sound you will hear is the sounds of plastic clasps.
We removed other peripherals from the frame so we could move the speaker/antenna module completely out of the way for photographing. You should not have to do this to replace just the fingerprint scanner.

Use a spudger to gently pry the left black plastic speaker/antenna module off of the frame as pictured. Start by lifting up the right side of the module, then slowly work your way down the module towards the right.

The slight cracking sound you will hear is the sounds of plastic clasps.

We removed other peripherals from the frame so we could move the speaker/antenna module completely out of the way for photographing. You should not have to do this to replace just the fingerprint scanner.

Step 10

Remove the 2mm bracket mounting screw from the frame using a Phillips #00 Screwdriver.
Lift up the bracket and set aside.

Remove the 2mm bracket mounting screw from the frame using a Phillips #00 Screwdriver.

Lift up the bracket and set aside.

Step 11

Open the ribbon cable clamp and pull the cable out.
You may require tweezers to slide the ribbon cable out of the clamp.
Lift out the fingerprint scanner.

Open the ribbon cable clamp and pull the cable out.

You may require tweezers to slide the ribbon cable out of the clamp.

Lift out the fingerprint scanner.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 4 other contributors

                    Hunter Baird-Wise

Member since: 04/18/2019

447 Reputation

                                      2 Guides authored                  



                       Badges:
                       6







                                                        +3 more badges

Team

                       Cal Poly, Team S9-G12, Maness Spring 2019                        

                                                  Member of Cal Poly, Team S9-G12, Maness Spring 2019 



                    CPSU-MANESS-S19S9G12                     


                                            4 Members                     


                                            5 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team