Hp Elite X2 1013 G3 Solid State Drive Replacement Repair Guide

Difficulty

Easy

Steps

8

Time Required

                          20 minutes            

Sections

3

• Screen
• 4 steps
• Battery
• 2 steps
• Solid State Drive
• 2 steps

Flags

1

Action Shots

Be an action hero! This guide needs images that better demonstrate how to perform specific actions.

• BackHP Elite X2 1013 G3

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              Screen               

• Flip the device over so the base is facing the ceiling.
• Lift up the tablet stand.
• Remove the four 2 mm screws from the tablet using a T5 Torx screwdriver.

Flip the device over so the base is facing the ceiling.

Lift up the tablet stand.

Remove the four 2 mm screws from the tablet using a T5 Torx screwdriver.

1024

Step 2

• Flip the tablet over with the screen facing upwards.
• Place the suction handle in the center of the screen and slowly lift off the screen until it is at a 30 degree angle, starting by gently prying up the bottom.
• Do not pull the screen beyond a 30 degree angle. Additional internal components must be disconnected first.

Flip the tablet over with the screen facing upwards.

Place the suction handle in the center of the screen and slowly lift off the screen until it is at a 30 degree angle, starting by gently prying up the bottom.

Do not pull the screen beyond a 30 degree angle. Additional internal components must be disconnected first.

Step 3

• With the screen lifted at a 30 degree angle, gently disconnect the yellow ribbon cable at the end connected to the screen.
• Gently disconnect the orange ribbon cable at the end connected to the bottom plate.

With the screen lifted at a 30 degree angle, gently disconnect the yellow ribbon cable at the end connected to the screen.

Gently disconnect the orange ribbon cable at the end connected to the bottom plate.

Step 4

• Remove the screen from the tablet.

Remove the screen from the tablet.

Step 5

              Battery               

• Use the Phillips #00 screwdriver to remove the six 2 mm screws.
• Gently disconnect the two connectors.

Use the Phillips #00 screwdriver to remove the six 2 mm screws.

Gently disconnect the two connectors.

Step 6

• Lift the battery out of the housing.

Lift the battery out of the housing.

Step 7

              Solid State Drive               

• Make sure the device is powered off and the battery is removed before continuing!
• Using the Phillips #00 Screwdriver, remove the single indicated screw.

Make sure the device is powered off and the battery is removed before continuing!

Using the Phillips #00 Screwdriver, remove the single indicated screw.

Step 8

• Gently tilt the drive upward, then firmly pull it out from the motherboard.
• Pay attention to the orientation of the SSD. Trying to put your replacement SSD in the wrong way could damage the part or the connector.

Gently tilt the drive upward, then firmly pull it out from the motherboard.

Pay attention to the orientation of the SSD. Trying to put your replacement SSD in the wrong way could damage the part or the connector.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.                                             

Author

                                      with 4 other contributors 

                    Kory Haydon                     

Member since: 04/18/2019

259 Reputation

                                      2 Guides authored                  



                       Badges:
                       6







                                                        +3 more badges                           

Team

                       Cal Poly, Team S9-G12, Maness Spring 2019                        

                                                  Member of Cal Poly, Team S9-G12, Maness Spring 2019 



                    CPSU-MANESS-S19S9G12                     


                                            4 Members                     


                                            5 Guides authored