Difficulty
Moderate
Steps
10
Time Required
45 minutes - 2 hours
Sections
2
- Battery
- 2 steps
- Screen
- 8 steps
Flags
0
BackHP Elitebook 2740p
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Slide the lock tab to the right.
Slide the lock tab to the right.
1024
Step 2
- Lift and remove the battery from the battery compartment.
Lift and remove the battery from the battery compartment.
Step 3
Screen
- Locate the radio antenna on the right side of the top edge of the screen. Slide the latch to release the antenna.
- Use a Phillips #0 screwdriver to remove the two 4 mm screws recessed in the antenna housing.
Locate the radio antenna on the right side of the top edge of the screen. Slide the latch to release the antenna.
Use a Phillips #0 screwdriver to remove the two 4 mm screws recessed in the antenna housing.
Step 4
- Use a metal spudger to separate bezel from laptop body. there are tabs holding the bezel on along the entire bezel.
- Pay special attention to the hinge cover at the bottom. It has tabs at both the top and bottom.
- Remove the bezel from the laptop.
Use a metal spudger to separate bezel from laptop body. there are tabs holding the bezel on along the entire bezel.
Pay special attention to the hinge cover at the bottom. It has tabs at both the top and bottom.
Remove the bezel from the laptop.
Step 5
- Use a Phillips #0 screwdriver to remove the eight 4 mm screws that hold the frame of the screen in place.
- Use a Phillips #00 screwdriver to remove the single 3 mm screw at the corner of the frame.
Use a Phillips #0 screwdriver to remove the eight 4 mm screws that hold the frame of the screen in place.
Use a Phillips #00 screwdriver to remove the single 3 mm screw at the corner of the frame.
Step 6
- Use a Phillips #0 screwdriver to remove the two 4 mm screws that hold the tilt button in place.
- Remove the tilt button.
Use a Phillips #0 screwdriver to remove the two 4 mm screws that hold the tilt button in place.
Remove the tilt button.
Step 7
- Use a Phillips #0 screwdriver to remove the three screws that secure the tablet-mode button board.
- Disconnect the two blue ribbon cables and gently pull them free.
- Remove the PCB board from the screen housing.
Use a Phillips #0 screwdriver to remove the three screws that secure the tablet-mode button board.
Disconnect the two blue ribbon cables and gently pull them free.
Remove the PCB board from the screen housing.
Step 8
- Remove the gray rubber pad at the top of the screen next to the camera.
- Remove the 3mm screw with a Phillips #0 screwdriver
- Carefully tilt the screen down onto the keayboard
Remove the gray rubber pad at the top of the screen next to the camera.
Remove the 3mm screw with a Phillips #0 screwdriver
Carefully tilt the screen down onto the keayboard
Step 9
- Fold the protective foil back from the ribbon cables.
Fold the protective foil back from the ribbon cables.
Step 10
- Unseat display ribbon cables.
- Ribbon cables are secured with tape. Do not force the cables out of their sockets.
- Remove the screen.
Unseat display ribbon cables.
Ribbon cables are secured with tape. Do not force the cables out of their sockets.
Remove the screen.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 1 other contributor
Joseph Hazel
Member since: 03/24/2017
305 Reputation
2 Guides authored
Badges:
7
+4 more badges
Team
UMass Dartmouth, Team S8-G4, Valliere Spring 2018
Member of UMass Dartmouth, Team S8-G4, Valliere Spring 2018
UMASSD-VALLIERE-S18S8G4
3 Members
6 Guides authored
