Difficulty
Moderate
Steps
7
Time Required
15 minutes
Sections
1
- Display
- 7 steps
Flags
0
BackHP Elitebook 8570w
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Display
- With the computer opened, locate the square buttons on both bottom corners of the display.
- Using a tool or finger, wedge the squares off revealing a screw on each corner.
With the computer opened, locate the square buttons on both bottom corners of the display.
Using a tool or finger, wedge the squares off revealing a screw on each corner.
1024
Step 2
- Use a T9 screwdriver to unscrew both 0.4mm Torx screws.
Use a T9 screwdriver to unscrew both 0.4mm Torx screws.
Step 3
- Use an opening tool or spudger to peel back the outer rim of the display.
- Continue to peel back the entire rim.
Use an opening tool or spudger to peel back the outer rim of the display.
Continue to peel back the entire rim.
Step 4
- Unscrew ONLY the bottom 0.8mm T9 Torx screw on both sides of the display.
Unscrew ONLY the bottom 0.8mm T9 Torx screw on both sides of the display.
Step 5
- Now locate the two screws on each side at the bottom of the display.
- TOP screw: unscrew partially.
- BOTTOM screw: completely unscrew and set to the side.
- Complete on both sides of display.
- Carefully separate the display from the top cover.
- Be sure to not let the top cover fall back
Now locate the two screws on each side at the bottom of the display.
TOP screw: unscrew partially.
BOTTOM screw: completely unscrew and set to the side.
Complete on both sides of display.
Carefully separate the display from the top cover.
Be sure to not let the top cover fall back
Step 6
- Use a Phillips #00 screwdriver to unscrew all four 0.8 mm screws from the left side of the display frame. Repeat for the right side.
- Push the metal plates/rods that were attached to the display towards the top cover.
- The display should be completely free of the top cover and able to lay flat on the keyboard (refer to photo #2).
Use a Phillips #00 screwdriver to unscrew all four 0.8 mm screws from the left side of the display frame. Repeat for the right side.
Push the metal plates/rods that were attached to the display towards the top cover.
The display should be completely free of the top cover and able to lay flat on the keyboard (refer to photo #2).
Step 7
- With the display laying on the keyboard, locate the black square panel marked in the photo.
- Grab the side marked in photo #2 and pull it towards you peeling off the surrounding tape and releasing it from the actual display board.
- This will then remove the connection between the display and the top cover.
With the display laying on the keyboard, locate the black square panel marked in the photo.
Grab the side marked in photo #2 and pull it towards you peeling off the surrounding tape and releasing it from the actual display board.
This will then remove the connection between the display and the top cover.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
4 other people completed this guide.
Author
with 2 other contributors
MJ Routh
Member since: 11/06/2017
461 Reputation
3 Guides authored
Badges:
7
+4 more badges
Team
Baylor, Team S8-G5, Johnson Fall 2017
Member of Baylor, Team S8-G5, Johnson Fall 2017
BU-JOHNSON-F17S8G5
3 Members
4 Guides authored
adrenochrome - Jan 16, 2018
Reply
this guide is really bad, dangerous and should be removed !
at step 3 you crack and kill the existing display. If it was still somewhat working before now you are assured it is completely dead !
