Hp Elitepad 1000 G2 Battery Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          10 - 20 minutes

Sections

Display
5 steps
NFC Antenna
2 steps
Battery
5 steps

Flags

BackHP ElitePad 1000 G2
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

If you have gone through the rest of the guide and a replacement of your battery seems to be the solution then this guide will help you fix it.

If you suspect your device has a swollen battery use this guide as reference.

What you need

Step 1

              Display

Before disassembling the tablet: make sure the tablet is off, disconnect the power cord from the tablet, and disconnect all external devices from the tablet.
Using a Phillips #00 screwdriver, remove the two Phillips PM 1.4×3.2mm screws located next to the charging port.

Before disassembling the tablet: make sure the tablet is off, disconnect the power cord from the tablet, and disconnect all external devices from the tablet.

Using a Phillips #00 screwdriver, remove the two Phillips PM 1.4×3.2mm screws located next to the charging port.

1024

Step 2

Place the suction cup on the lower right corner of the tablet display glass, making sure to place the suction cup inside the edges of the border of the display glass.
Insert a plastic pick in between the display and the tablet case. Then use a plastic removal tool to separate the display further.
Pull on the suction cup while using the prying tool to separate the display from the tablet.
Gently lift the display from the tablet in order to avoid damaging the cables.

Place the suction cup on the lower right corner of the tablet display glass, making sure to place the suction cup inside the edges of the border of the display glass.

Insert a plastic pick in between the display and the tablet case. Then use a plastic removal tool to separate the display further.

Pull on the suction cup while using the prying tool to separate the display from the tablet.

Gently lift the display from the tablet in order to avoid damaging the cables.

Step 3

To disconnect the cables, use the spudger tool to gently pull back on the black tab located on the side of the connector while gently pulling the cable.
Release the zero insertion force (ZIF) connector to which the TouchScreen cable is attached, and then disconnect the TouchScreen cable from the system board.

To disconnect the cables, use the spudger tool to gently pull back on the black tab located on the side of the connector while gently pulling the cable.

Release the zero insertion force (ZIF) connector to which the TouchScreen cable is attached, and then disconnect the TouchScreen cable from the system board.

Step 4

Release the ZIF connector to which the display cable is attached, and then disconnect the display cable from the system board.

Release the ZIF connector to which the display cable is attached, and then disconnect the display cable from the system board.

Step 5

Remove the display from the tablet.

Remove the display from the tablet.

Step 6

              NFC Antenna

Locate the NFC antenna.
Release the ZIF connector to which the NFC antenna cable is attached.
To disconnect the cable, use the plastic prying tool to gently push on the tab located on the side of the connector.

Locate the NFC antenna.

Release the ZIF connector to which the NFC antenna cable is attached.

To disconnect the cable, use the plastic prying tool to gently push on the tab located on the side of the connector.

Step 7

Detach the NFC antenna from the surface of the system board.
The NFC antenna is attached to the system board with double-sided adhesive.
Remove the NFC antenna.

Detach the NFC antenna from the surface of the system board.

The NFC antenna is attached to the system board with double-sided adhesive.

Remove the NFC antenna.

Step 8

              Battery

Locate the power button board ribbon cable.
Locate the battery to motherboard connector.

Locate the power button board ribbon cable.

Locate the battery to motherboard connector.

Step 9

Lift the clear tape attached to the power button board ribbon cable.
Disconnect the ZIF connector by using a plastic removal tool to gently pull up on the black tab.
Lift the power button board ribbon cable up and away so that it doesn’t get in the way of the battery during removal.

Lift the clear tape attached to the power button board ribbon cable.

Disconnect the ZIF connector by using a plastic removal tool to gently pull up on the black tab.

Lift the power button board ribbon cable up and away so that it doesn’t get in the way of the battery during removal.

Step 10

Disconnect the battery to system board connector by pushing gently on it with a plastic pry tool and then pull it away from the system board.

Disconnect the battery to system board connector by pushing gently on it with a plastic pry tool and then pull it away from the system board.

Step 11

Using a philips 00 screw driver take out the six Phillips PM1.3×2.0mm screws

Using a philips 00 screw driver take out the six Phillips PM1.3×2.0mm screws

Step 12

Carefully lift the battery away from the bottom cover.

Carefully lift the battery away from the bottom cover.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      7 other people completed this guide.

Author

                                      with 3 other contributors

                    Vanessa Onyullo

Member since: 07/08/2019

371 Reputation

                                      2 Guides authored                  



                       Badges:
                       7







                                                        +4 more badges

Team

                       Embry-Riddle Aeronautical University, Team S3-G2, Watkins Summer 2019                        

                                                  Member of Embry-Riddle Aeronautical University, Team S3-G2, Watkins Summer 2019 



                    ERAU-WATKINS-SU19S3G2                     


                                            4 Members                     


                                            6 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team