Hp Elitepad 1000 G2 Power Volume Button Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          10 - 15 minutes

Sections

Display
5 steps
NFC Antenna
2 steps
Power/Volume button
7 steps

Flags

BackHP ElitePad 1000 G2
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Display

Before disassembling the tablet: make sure the tablet is off, disconnect the power cord from the tablet, and disconnect all external devices from the tablet.
Using a Phillips #00 screwdriver, remove the two Phillips PM 1.4×3.2mm screws located next to the charging port.

Before disassembling the tablet: make sure the tablet is off, disconnect the power cord from the tablet, and disconnect all external devices from the tablet.

Using a Phillips #00 screwdriver, remove the two Phillips PM 1.4×3.2mm screws located next to the charging port.

1024

Step 2

Place the suction cup on the lower right corner of the tablet display glass, making sure to place the suction cup inside the edges of the border of the display glass.
Insert a plastic pick in between the display and the tablet case. Then use a plastic removal tool to separate the display further.
Pull on the suction cup while using the prying tool to separate the display from the tablet.
Gently lift the display from the tablet in order to avoid damaging the cables.

Place the suction cup on the lower right corner of the tablet display glass, making sure to place the suction cup inside the edges of the border of the display glass.

Insert a plastic pick in between the display and the tablet case. Then use a plastic removal tool to separate the display further.

Pull on the suction cup while using the prying tool to separate the display from the tablet.

Gently lift the display from the tablet in order to avoid damaging the cables.

Step 3

To disconnect the cables, use the spudger tool to gently pull back on the black tab located on the side of the connector while gently pulling the cable.
Release the zero insertion force (ZIF) connector to which the TouchScreen cable is attached, and then disconnect the TouchScreen cable from the system board.

To disconnect the cables, use the spudger tool to gently pull back on the black tab located on the side of the connector while gently pulling the cable.

Release the zero insertion force (ZIF) connector to which the TouchScreen cable is attached, and then disconnect the TouchScreen cable from the system board.

Step 4

Release the ZIF connector to which the display cable is attached, and then disconnect the display cable from the system board.

Release the ZIF connector to which the display cable is attached, and then disconnect the display cable from the system board.

Step 5

Remove the display from the tablet.

Remove the display from the tablet.

Step 6

              NFC Antenna

Locate the NFC antenna.
Release the ZIF connector to which the NFC antenna cable is attached.
To disconnect the cable, use the plastic prying tool to gently push on the tab located on the side of the connector.

Locate the NFC antenna.

Release the ZIF connector to which the NFC antenna cable is attached.

To disconnect the cable, use the plastic prying tool to gently push on the tab located on the side of the connector.

Step 7

Detach the NFC antenna from the surface of the system board.
The NFC antenna is attached to the system board with double-sided adhesive.
Remove the NFC antenna.

Detach the NFC antenna from the surface of the system board.

The NFC antenna is attached to the system board with double-sided adhesive.

Remove the NFC antenna.

Step 8

              Power/Volume button

Locate the power button board and attached ribbon cable.
Locate the volume button board.

Locate the power button board and attached ribbon cable.

Locate the volume button board.

Step 9

Disconnect the volume button board cable from the power button board.
Disconnect the left microphone cable from the power button board.
For both of these connectors, there’s a thin seam in the middle. To disconnect, wedge your tool in between the seam and firmly, but carefully push.

Disconnect the volume button board cable from the power button board.

Disconnect the left microphone cable from the power button board.

For both of these connectors, there’s a thin seam in the middle. To disconnect, wedge your tool in between the seam and firmly, but carefully push.

Step 10

Lift the clear tape which is attached to the power button board cable and the motherboard.
Release the ZIF connector to which the power button board cable is attached.
Detach the power button board cable from the surface of the battery by pulling away from the connector.
The power button board cable is attached to the battery with double-sided adhesive.

Lift the clear tape which is attached to the power button board cable and the motherboard.

Release the ZIF connector to which the power button board cable is attached.

Detach the power button board cable from the surface of the battery by pulling away from the connector.

The power button board cable is attached to the battery with double-sided adhesive.

Step 11

Remove the Phillips PM1.3×2.0mm broad head screw and the Phillips PM1.3×2.0mm screw that secure the power button board to the bottom cover.
Gently push upwards on the tab

Remove the Phillips PM1.3×2.0mm broad head screw and the Phillips PM1.3×2.0mm screw that secure the power button board to the bottom cover.

Gently push upwards on the tab

Step 12

Remove the power button board and cable.

Remove the power button board and cable.

Step 13

Remove the two Phillips PM1.5×2.0mm screws that secure the volume button board to the bottom cover.

Remove the two Phillips PM1.5×2.0mm screws that secure the volume button board to the bottom cover.

Step 14

Remove the volume button board and cable.

Remove the volume button board and cable.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors

                    Vanessa Onyullo

Member since: 07/08/2019

371 Reputation

                                      2 Guides authored                  



                       Badges:
                       7







                                                        +4 more badges

Team

                       Embry-Riddle Aeronautical University, Team S3-G2, Watkins Summer 2019                        

                                                  Member of Embry-Riddle Aeronautical University, Team S3-G2, Watkins Summer 2019 



                    ERAU-WATKINS-SU19S3G2                     


                                            4 Members                     


                                            6 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team