Difficulty

Moderate

Steps

9

Time Required

                          30 - 45 minutes

Sections

3

  • Back Panel
  • 2 steps
  • Cooling Fan
  • 2 steps
  • Motherboard
  • 5 steps

Flags

1

Better Introduction

Improve this guide by completing or revising its introduction.

  • BackHP Envy Touchsmart m6-k125dx

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

What you need

Step 1

              Back Panel
  • Turn the laptop over so that the bottom is facing up
  • Using the J0 screwdriver, unscrew all 12 M2.5x5.5 screws from the back panel.

Turn the laptop over so that the bottom is facing up

Using the J0 screwdriver, unscrew all 12 M2.5x5.5 screws from the back panel.

1024

Step 2

  • Carefully remove the back panel to reveal the inner components.

Carefully remove the back panel to reveal the inner components.

Step 3

              Cooling Fan
  • Use the J0 screwdriver to remove the two M2.0x3.0 screws holding in the cooling fan

Use the J0 screwdriver to remove the two M2.0x3.0 screws holding in the cooling fan

Step 4

  • Unplug the cord and carefully remove the cooling fan

Unplug the cord and carefully remove the cooling fan

Step 5

              Motherboard
  • Use the J1 screwdriver to remove the three M2.5x2.5 screws on the SD card reader.
  • Remove the SD card reader and set it aside.

Use the J1 screwdriver to remove the three M2.5x2.5 screws on the SD card reader.

Remove the SD card reader and set it aside.

Step 6

  • Disconnect the six ZIF connectors.
  • Use the tweezers to flip up the plastic retaining flap.
  • Pull the cable out horizontally.

Disconnect the six ZIF connectors.

Use the tweezers to flip up the plastic retaining flap.

Pull the cable out horizontally.

Step 7

  • Disconnect the four remaining connectors.
  • Use a plastic opening tool or spudger if necessary to pry the connector apart.

Disconnect the four remaining connectors.

Use a plastic opening tool or spudger if necessary to pry the connector apart.

Step 8

  • Use the J0 screwdriver to remove the two M2.5x2.5 screws on the wireless network card.
  • Slide the card horizontally toward the front of the laptop and out of its socket.

Use the J0 screwdriver to remove the two M2.5x2.5 screws on the wireless network card.

Slide the card horizontally toward the front of the laptop and out of its socket.

Step 9

  • Use the J1 screwdriver to remove the four M2.5x2.5 screws that secure the motherboard to the case.
  • Pull up on the right side of the motherboard, away from the USB ports, then slide out to the right.

Use the J1 screwdriver to remove the four M2.5x2.5 screws that secure the motherboard to the case.

Pull up on the right side of the motherboard, away from the USB ports, then slide out to the right.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors 


                    Alan Orr

Member since: 04/06/2019

139 Reputation

                                      1 Guide authored                  



                       Badges:
                       6







                                                        +3 more badges

Team

                       IUPUI, Team S14-G14, Wilson Spring 2019                        

                                                  Member of IUPUI, Team S14-G14, Wilson Spring 2019 



                    IUPUI-WILSON-S19S14G14                     


                                            4 Members                     


                                            3 Guides authored