Hp Envy X360 15M Bq021Dx Cooling Fan Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          5 - 15 minutes

Sections

Battery
5 steps
Cooling Fan
4 steps

Flags

BackHP Envy x360 15m-bq021dx
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

On the back panel of the device, remove the four (4) M2.5xL6 screws at the top of the photo using a Phillips #0 screwdriver.
Unscrew the three (3) screws at the bottom of the photo using a T5 Torx screwdriver.

On the back panel of the device, remove the four (4) M2.5xL6 screws at the top of the photo using a Phillips #0 screwdriver.

Unscrew the three (3) screws at the bottom of the photo using a T5 Torx screwdriver.

1024

Step 2

To remove the back cover, use the black spudger to lift up on the edges of the cover.
Use a suction cup to assist in lifting the back cover

To remove the back cover, use the black spudger to lift up on the edges of the cover.

Use a suction cup to assist in lifting the back cover

Step 3

Use the Philips #0 screwdriver to remove six (6) M2.0x3.2 screws from battery.

Use the Philips #0 screwdriver to remove six (6) M2.0x3.2 screws from battery.

Step 4

Using the Philips #0 screwdriver, remove the final screw from the battery connected to the SSD storage unit.

Using the Philips #0 screwdriver, remove the final screw from the battery connected to the SSD storage unit.

Step 5

Lift and pull the front of the battery up and out (away from the connector) to remove.

Lift and pull the front of the battery up and out (away from the connector) to remove.

Step 6

              Cooling Fan

Using a Philips #0 screwdriver, remove the three M2x4 screws located around the cooling fan as shown in this picture.
Be careful as the fan might be sharp in some places when removing it.

Using a Philips #0 screwdriver, remove the three M2x4 screws located around the cooling fan as shown in this picture.

Be careful as the fan might be sharp in some places when removing it.

Step 7

Remove the connector clip with the tweezers.

Remove the connector clip with the tweezers.

Step 8

Remove the four spring loaded screws with a Philips #1 screwdriver.

Remove the four spring loaded screws with a Philips #1 screwdriver.

Step 9

Remove the cooling fan.

Remove the cooling fan.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.

Author

                                      with 4 other contributors

                    SALMAN ALOTAIBI

Member since: 09/04/2019

139 Reputation

                                      1 Guide authored                  



                       Badges:
                       7







                                                        +4 more badges

Team

                       University of Alabama, Team S2-G6, Bedsole Fall 2019                        

                                                  Member of University of Alabama, Team S2-G6, Bedsole Fall 2019 



                    UA-BEDSOLE-F19S2G6                     


                                            4 Members                     


                                            5 Guides authored

Daniel Abrams - Jul 21, 2021

I’m considering attempting this repair. I am curious as to why the instructions direct me to remove the battery before removing the fan. From the pictures shown above, it does not appear that battery is mechanically blocking the removal of the fan. Is the purpose of this step to remove a phisical impedance, or is the reason to remove power from the he device?

Introduction#

What you need#

Team#

Introduction

What you need

Team