Hp Envy X360 M6 Aq003Dx Display Screen Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          20 - 25 minutes

Sections

Back Panel
3 steps
Battery
2 steps
Display Screen
7 steps

Flags

BackHP Envy x360 m6-aq003dx
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Back Panel

Turn the laptop over and use the plastic opening tool to take off the rubber pads. You only need to take off the two pads at the top for this device.

Turn the laptop over and use the plastic opening tool to take off the rubber pads. You only need to take off the two pads at the top for this device.

1024

Step 2

Use the Torx T5 screwdriver to remove the six small screws.
Use the Phillips #0 screwdriver to remove the screws under the rubber pads in step 1.

Use the Torx T5 screwdriver to remove the six small screws.

Use the Phillips #0 screwdriver to remove the screws under the rubber pads in step 1.

Step 3

Go slowly around the edge with the opening tool. The noises you will hear are due to the small joints popping open. Continue this until you have made your way around the entire laptop.

Go slowly around the edge with the opening tool. The noises you will hear are due to the small joints popping open. Continue this until you have made your way around the entire laptop.

Step 4

              Battery

Remove the six 4mm screws around the battery using a Phillips #0 screwdriver.

Remove the six 4mm screws around the battery using a Phillips #0 screwdriver.

Step 5

Disconnect the white connector from the battery to the board. (It is recommended to use pliers to remove the cord to avoid touching the board).
Once the connector and screws are both removed, lift the battery up and remove it from the laptop.
The removal of the connector and the screws can be done in either order.

Disconnect the white connector from the battery to the board. (It is recommended to use pliers to remove the cord to avoid touching the board).

Once the connector and screws are both removed, lift the battery up and remove it from the laptop.

The removal of the connector and the screws can be done in either order.

Step 6

              Display Screen

Make sure the the back panel is placed back on the computer so none of the internal components are exposed.
Open laptop and lay it completely flat.

Make sure the the back panel is placed back on the computer so none of the internal components are exposed.

Open laptop and lay it completely flat.

Step 7

Place the suction cup directly on the screen and apply pressure so that the cup is firmly in place.

Place the suction cup directly on the screen and apply pressure so that the cup is firmly in place.

Step 8

Take the opening tool and wedge it between the rubber lining around the screen and the back panel and begin to pry it open by lifting up.

Take the opening tool and wedge it between the rubber lining around the screen and the back panel and begin to pry it open by lifting up.

Step 9

To take the screen out of the back panel, simultaneously pull on the suction cup while creating leverage between the back panel and the rubber lining.
Popping sounds are expected.

To take the screen out of the back panel, simultaneously pull on the suction cup while creating leverage between the back panel and the rubber lining.

Popping sounds are expected.

Step 10

Once the screen is detached from the back panel, direct your attention to the back of the screen where you will remove the tape holding the screen to the bottom panel.
Remove the grey tape covering the wires on both sides by slowly pulling back the tape as not to separate the tape from the adhesive.

Once the screen is detached from the back panel, direct your attention to the back of the screen where you will remove the tape holding the screen to the bottom panel.

Remove the grey tape covering the wires on both sides by slowly pulling back the tape as not to separate the tape from the adhesive.

Step 11

Remove the slender black wire that is connected to the bread board by sliding the cable backwards.
Pull down on the tape connected to the cable while sliding it out in order to completely detach all screen connections from the back panel.

Remove the slender black wire that is connected to the bread board by sliding the cable backwards.

Pull down on the tape connected to the cable while sliding it out in order to completely detach all screen connections from the back panel.

Step 12

Once steps 1-6 are completed, place a hand on the edge of the screen and slowly pull the screen away from the back panel and remove it from the device.

Once steps 1-6 are completed, place a hand on the edge of the screen and slowly pull the screen away from the back panel and remove it from the device.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 5 other contributors

                    Rachel_Jones

Member since: 09/25/2019

177 Reputation

                                      1 Guide authored                  



                       Badges:
                       4







                                                        +1 more badge

Team

                       Embry-Riddle Aeronautical University, Team S13-G3, Lamothe Fall 2019                        

                                                  Member of Embry-Riddle Aeronautical University, Team S13-G3, Lamothe Fall 2019 



                    ERAU-LAMOTHE-F19S13G3                     


                                            4 Members                     


                                            5 Guides authored

Bessie - Oct 5, 2022

Thank you for the great illustration with pictures and detailed steps! great job!

Introduction#

What you need#

Team#

Introduction

What you need

Team