Difficulty

Difficult

Steps

14

Time Required

                          45 minutes - 1 hour

Sections

3

  • Keyboard
  • 4 steps
  • Battery
  • 3 steps
  • Display
  • 7 steps

Flags

1

Incorrect Tools

Help make this guide better by using the correct tools in images and/or text.

  • BackHP Envy x360 m6-w103dx

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

Make sure the computer is unplugged and powered off before touching any internal parts.

Removing the display doesn’t require any special technical skills. This is not dangerous, but caution is recommended to keep from breaking the screen.

What you need

Step 1

              Keyboard
  • Before you begin, be sure to power off your laptop.
  • Using an opening pick, remove the 4 rubber feet and 4 screw covers.

Before you begin, be sure to power off your laptop.

Using an opening pick, remove the 4 rubber feet and 4 screw covers.

1024

Step 2

  • Unscrew the twelve 6 mm screws from the bottom of the laptop using a Phillips #0 screwdriver.

Unscrew the twelve 6 mm screws from the bottom of the laptop using a Phillips #0 screwdriver.

Step 3

  • Open the laptop carefully, with the keyboard face up.
  • Pry around the outside of the keyboard with the plastic opening tool until the keyboard can be lifted slightly.
  • When lifting the keyboard do not pull too hard. There are cables that must be disconnected before the keyboard can be removed.

Open the laptop carefully, with the keyboard face up.

Pry around the outside of the keyboard with the plastic opening tool until the keyboard can be lifted slightly.

When lifting the keyboard do not pull too hard. There are cables that must be disconnected before the keyboard can be removed.

Step 4

  • Lift the keyboard until you can see the cables connected to the motherboard.
  • Gently lift the tab on each ZIF connector that connects each cable to the motherboard using a spudger. Once each tab is flipped up, the corresponding ribbon cable will come out easily.
  • Detach the keyboard.

Lift the keyboard until you can see the cables connected to the motherboard.

Gently lift the tab on each ZIF connector that connects each cable to the motherboard using a spudger. Once each tab is flipped up, the corresponding ribbon cable will come out easily.

Detach the keyboard.

Step 5

              Battery
  • Remove the four 6 mm Phillips #0 screws holding the battery in place.
  • The white arrows on the battery point to where each screw is.

Remove the four 6 mm Phillips #0 screws holding the battery in place.

The white arrows on the battery point to where each screw is.

Step 6

  • Unplug the ribbon cable by flipping up the white tabs on the ZIF connectors and gently sliding the ribbon cables out of their sockets.
  • Unplug the battery connector by grasping the small white tabs on either side of the connector and pulling down towards the battery.

Unplug the ribbon cable by flipping up the white tabs on the ZIF connectors and gently sliding the ribbon cables out of their sockets.

Unplug the battery connector by grasping the small white tabs on either side of the connector and pulling down towards the battery.

Step 7

  • Lift out the battery.
  • You may need to peel off the ribbon cable and replace it after installing the new battery if your replacement part doesn’t have one already adhered.

Lift out the battery.

You may need to peel off the ribbon cable and replace it after installing the new battery if your replacement part doesn’t have one already adhered.

Step 8

              Display
  • Remove the six 6 mm screws from the hinges with a Phillips #0 screwdriver.

Remove the six 6 mm screws from the hinges with a Phillips #0 screwdriver.

Step 9

  • Carefully remove the display from the laptop.

Carefully remove the display from the laptop.

Step 10

  • Remove the screen from the rest of the display using a spudger.

Remove the screen from the rest of the display using a spudger.

Step 11

  • Remove the tape on the bottom right of the display with tweezers.

Remove the tape on the bottom right of the display with tweezers.

Step 12

  • Remove the tape and disconnect the ribbon from the top right of the display using blunt tweezers.

Remove the tape and disconnect the ribbon from the top right of the display using blunt tweezers.

Step 13

  • Remove the display bezel using a spudger.

Remove the display bezel using a spudger.

Step 14

  • Carefully pry up the display from the bezel.

Carefully pry up the display from the bezel.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors 


                    Tyler

Member since: 09/21/2021

145 Reputation

                                      1 Guide authored                  



                       Badges:
                       3

Team

                       The Citadel Military College of South Carolina, Team 3-20, Eggleston Fall 2021                        

                                                  Member of The Citadel Military College of South Carolina, Team 3-20, Eggleston Fall 2021 



                    CMCSC-EGGLESTON-F21S3G20                     


                                            3 Members                     


                                            3 Guides authored