Hp Mini 110 3131Dx Keyboard Bezel Replacement Repair Guide

Difficulty

Moderate

Steps

10

Time Required

                          20 minutes            

Sections

5

• Battery
• 1 step
• Back Cover
• 1 step
• Hard Drive
• 2 steps
• Keyboard
• 3 steps
• Keyboard Bezel
• 3 steps

Flags

3

Needs More Images

A few more images would make this guide’s procedures crystal clear.

Incorrect Tools

Help make this guide better by using the correct tools in images and/or text.

Better Introduction

Improve this guide by completing or revising its introduction.

• BackHP Mini 110-3131dx

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

What you need

Step 1

              Battery               

• Power off the laptop before trying to remove the battery.
• Turn the laptop upside down, and locate the sliding tabs on the battery.
• Slide both tabs in an inward direction, then slide the battery away from the laptop.

Power off the laptop before trying to remove the battery.

Turn the laptop upside down, and locate the sliding tabs on the battery.

Slide both tabs in an inward direction, then slide the battery away from the laptop.

1024

Step 2

              Back Cover               

• To remove the bottom cover pull the orange tab to the right until it clicks.
• Carefully disconnect the clips as you lift the bottom cover.

To remove the bottom cover pull the orange tab to the right until it clicks.

Carefully disconnect the clips as you lift the bottom cover.

Step 3

              Hard Drive               

• Remove the four screws holding down the hard drive using a Phillips #1 screwdriver.

Remove the four screws holding down the hard drive using a Phillips #1 screwdriver.

Step 4

• Lift the black flap covering the hard drive then slide it towards the left using the orange tab until it’s released from its receptacle.
• Pull the hard drive out of the laptop.
• Put the hard drive in an anti-static bag to decrease the likelihood of harming it with static electricity.

Lift the black flap covering the hard drive then slide it towards the left using the orange tab until it’s released from its receptacle.

Pull the hard drive out of the laptop.

Put the hard drive in an anti-static bag to decrease the likelihood of harming it with static electricity.

Step 5

              Keyboard               

• Remove the three black screws marked by the keyboard symbol using a Phillips #1 screwdriver.

Remove the three black screws marked by the keyboard symbol using a Phillips #1 screwdriver.

Step 6

• Turn the laptop upright and open it.
• Disconnect the clips located around the perimeter of the keyboard.
• Slide the iFixit opening tool between the top edge of the keyboard and the plastic bezel.
• Start either above the esc key or the delete key.
• Pull the keyboard with your fingers until it comes out on both sides.
• Be careful not to pull the keyboard out too fast. There is a fragile ribbon cable that attaches to the motherboard behind the keyboard.

Turn the laptop upright and open it.

Disconnect the clips located around the perimeter of the keyboard.

Slide the iFixit opening tool between the top edge of the keyboard and the plastic bezel.

Start either above the esc key or the delete key.

Pull the keyboard with your fingers until it comes out on both sides.

Be careful not to pull the keyboard out too fast. There is a fragile ribbon cable that attaches to the motherboard behind the keyboard.

Step 7

• Tilt the keyboard toward you to reveal the ribbon cable.
• Lift up the black tab on top of the keyboard ribbon cable to release the ribbon cable.
• Pull the ribbon cable out of its container.

Tilt the keyboard toward you to reveal the ribbon cable.

Lift up the black tab on top of the keyboard ribbon cable to release the ribbon cable.

Pull the ribbon cable out of its container.

Step 8

              Keyboard Bezel               

• Remove the six black screws around the perimeter of the laptop using a Phillips #1 screwdriver.
• Be sure to keep track of which screws go where as they are not all the same size.
• Flip the laptop over and remove the six black screws.

Remove the six black screws around the perimeter of the laptop using a Phillips #1 screwdriver.

Be sure to keep track of which screws go where as they are not all the same size.

Flip the laptop over and remove the six black screws.

Step 9

• Using your fingernail or the iFixit opening tool, flip the black tab up to release the ribbon cable that connects the touchpad and motherboard.
• Disconnect the red and black wires from the motherboard on the left-hand side of the bezel using your fingernail or iFixit opening tool.

Using your fingernail or the iFixit opening tool, flip the black tab up to release the ribbon cable that connects the touchpad and motherboard.

Disconnect the red and black wires from the motherboard on the left-hand side of the bezel using your fingernail or iFixit opening tool.

Step 10

• Lift the keyboard bezel from the back end and slide the iFixit opening tool around the perimeter of the bezel until it is fully released.

Lift the keyboard bezel from the back end and slide the iFixit opening tool around the perimeter of the bezel until it is fully released.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.                                             

Author

                                      with 7 other contributors 

                    aarondcollege                     

Member since: 10/06/2016

1,285 Reputation

                                      10 Guides authored                  



                       Badges:
                       14







                                                        +11 more badges                           

Team

                       USF Tampa, Team 2-4, Cagle Fall 2016                        

                                                  Member of USF Tampa, Team 2-4, Cagle Fall 2016 



                    USFT-CAGLE-F16S2G4                     


                                            5 Members                     


                                            10 Guides authored