Hp Mini 110 3735Dx Screen Replacement Repair Guide

Difficulty

Difficult

Steps

Time Required

                          25 minutes

Sections

Battery
2 steps
Backcover
1 step
Keyboard
7 steps
Hard Drive Cage
3 steps
Screen
23 steps

Flags

BackHP Mini 110-3735dx
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

With the bottom of the HP Mini facing up, slide both switches inward towards each other.

With the bottom of the HP Mini facing up, slide both switches inward towards each other.

1024

Step 2

With the left switch still pushed inward, pull the battery towards you to remove it from the computer.

With the left switch still pushed inward, pull the battery towards you to remove it from the computer.

Step 3

              Backcover

Pull upward from under the back cover via the missing battery area.
Best to start from one of the corners.

Pull upward from under the back cover via the missing battery area.

Best to start from one of the corners.

Step 4

              Keyboard

Remove the three 4.0 mm screws with the keyboard indicator next to them using a Phillips #1 screw driver.

Remove the three 4.0 mm screws with the keyboard indicator next to them using a Phillips #1 screw driver.

Step 5

Flip the laptop over, and open it up.
Don’t worry! No pieces will fall out.

Flip the laptop over, and open it up.

Don’t worry! No pieces will fall out.

Step 6

With the keyboard facing you, pull the black bezel upward until its loose.
You should hear three clicks.

With the keyboard facing you, pull the black bezel upward until its loose.

You should hear three clicks.

Step 7

Move and hold the bezel slightly towards the screen while lifting the keyboard from the top.

Move and hold the bezel slightly towards the screen while lifting the keyboard from the top.

Step 8

Pull up the keyboard from the bottom corners exposing the keyboard cable.

Pull up the keyboard from the bottom corners exposing the keyboard cable.

Step 9

Lift the black holder connected to the keyboard cable until it points up.

Lift the black holder connected to the keyboard cable until it points up.

Step 10

Gently pull the keyboard cable from the socket.

Gently pull the keyboard cable from the socket.

Step 11

              Hard Drive Cage

Remove the three 5.0 mm screws holding the hard drive cage in place using a Phillips #1 screw driver.

Remove the three 5.0 mm screws holding the hard drive cage in place using a Phillips #1 screw driver.

Step 12

Lift the hard drive cage by pulling the tape upward.
Start by pulling the tape from the side with the keyboard symbol.

Lift the hard drive cage by pulling the tape upward.

Start by pulling the tape from the side with the keyboard symbol.

Step 13

Unplug the cable connecting to the hard drive.

Unplug the cable connecting to the hard drive.

Step 14

              Screen

Remove the 8 5.0 mm screws under the keyboard using a Phillips #1 screw driver.

Remove the 8 5.0 mm screws under the keyboard using a Phillips #1 screw driver.

Step 15

Lift the two black holders upward located next to the socket for the keyboard close to the tracked pad.

Lift the two black holders upward located next to the socket for the keyboard close to the tracked pad.

Step 16

Remove the two connectors for the motherboard from their sockets.

Remove the two connectors for the motherboard from their sockets.

Step 17

Close the laptop by bringing the screen down.
Flip the laptop over to the other side.

Close the laptop by bringing the screen down.

Flip the laptop over to the other side.

Step 18

Remove the 6 5.0 mm screws holding the back plate together using a Phillips #1 screw driver.

Remove the 6 5.0 mm screws holding the back plate together using a Phillips #1 screw driver.

Step 19

Remove the 2 3.0 mm screw head holding the plastic piece in place using a Phillips #1 screw driver.
Located on the left and right side where the battery was removed.

Remove the 2 3.0 mm screw head holding the plastic piece in place using a Phillips #1 screw driver.

Located on the left and right side where the battery was removed.

Step 20

Pull the black plastic pieces that the screws was holding inward.
The pieces are located on the left and right corners connecting the bottom and top of the HP Mini.

Pull the black plastic pieces that the screws was holding inward.

The pieces are located on the left and right corners connecting the bottom and top of the HP Mini.

Step 21

Flip the laptop back over.
Open it by lifting the screeen.

Flip the laptop back over.

Open it by lifting the screeen.

Step 22

Right next to the previous plastic piece, remove the other two plastic pieces.
This may be difficult to come off. Tilt the screen back and forth to help loosen the piece.

Right next to the previous plastic piece, remove the other two plastic pieces.

This may be difficult to come off. Tilt the screen back and forth to help loosen the piece.

Step 23

Using the plastic prying tool, pry the front plate of the bottom part of your HP Mini.
Start along the speaker grill near the touch pad, and move along the sides.

Using the plastic prying tool, pry the front plate of the bottom part of your HP Mini.

Start along the speaker grill near the touch pad, and move along the sides.

Step 24

Lift up the front plate where the keyboard was.

Lift up the front plate where the keyboard was.

Step 25

Remove the display cable from the motherboard located on the top left corner under where the keyboard was by pulling on the black tab.
Move the cable.

Remove the display cable from the motherboard located on the top left corner under where the keyboard was by pulling on the black tab.

Move the cable.

Step 26

Remove the webcam cables from the motherboard.
Located on the back side of the laptop in the bottom left corner.

Remove the webcam cables from the motherboard.

Located on the back side of the laptop in the bottom left corner.

Step 27

Flip over the computer, and open the laptop.
Lift up the front plate on the top right corner.

Flip over the computer, and open the laptop.

Lift up the front plate on the top right corner.

Step 28

Pull the cables for the web cam out using tweezers.

Pull the cables for the web cam out using tweezers.

Step 29

Remove the 2 3.0 mm screws on both sides of the bottom of the display using a Phillips #1 screwdriver.

Remove the 2 3.0 mm screws on both sides of the bottom of the display using a Phillips #1 screwdriver.

Step 30

Remove the black plastic piece that the screw was holding on both sides.
This will reveal another screw.

Remove the black plastic piece that the screw was holding on both sides.

This will reveal another screw.

Step 31

Remove the 2 3.0 mm screws on both sides using a Phillips #1 screw driver.
When removing, keep hold of the screen to make sure it doesn’t fall.

Remove the 2 3.0 mm screws on both sides using a Phillips #1 screw driver.

When removing, keep hold of the screen to make sure it doesn’t fall.

Step 32

Pry the front plate using the plastic opening tool by pushing along the border of the front and back plate.
Make sure to pry from the sides, top and bottom as the corners will come undone themselves.

Pry the front plate using the plastic opening tool by pushing along the border of the front and back plate.

Make sure to pry from the sides, top and bottom as the corners will come undone themselves.

Step 33

Remove the front plate.
Pull the cables through the holes.

Remove the front plate.

Pull the cables through the holes.

Step 34

Remove the 4 4.0 mm screws holding the screen in place using a Phillips #1 screw driver.

Remove the 4 4.0 mm screws holding the screen in place using a Phillips #1 screw driver.

Step 35

Lift the screen up.

Lift the screen up.

Step 36

Under the screen, peel off the tape near the cable completely, so you can see the socket for the cable.

Under the screen, peel off the tape near the cable completely, so you can see the socket for the cable.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors

                    Tyrone Williams

Member since: 03/10/2016

905 Reputation

                                      7 Guides authored                  



                       Badges:
                       10







                                                        +7 more badges

Team

                       UMass Dartmouth, Team 4-1, Catania Spring 2016                        

                                                  Member of UMass Dartmouth, Team 4-1, Catania Spring 2016 



                    UMASSD-CATANIA-S16S4G1                     


                                            4 Members                     


                                            7 Guides authored

Icela Ross - Sep 21, 2017

Tengo una pregunta en pantalla habrá alguna otra que sea compatible con esta hp sin ser el mismo modelo?

Introduction#

What you need#

Team#

Introduction

What you need

Team