Difficulty
Easy
Steps
7
Time Required
15 - 30 minutes
Sections
2
- Battery
- 4 steps
- Ventilation Fans
- 3 steps
Flags
0
BackHP Omen 15-ax243dx
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- The rear panel is secured by 10 screws. Using a #00 Phillips Screwdriver, remove the ten 1.2 mm screws.
- The screwdriver should be inserted at the same angle as the screws.
- Be sure to keep track of the screws and where they came from. Some only fit in to one spot.
The rear panel is secured by 10 screws. Using a #00 Phillips Screwdriver, remove the ten 1.2 mm screws.
The screwdriver should be inserted at the same angle as the screws.
Be sure to keep track of the screws and where they came from. Some only fit in to one spot.
1024
Step 2
- Insert a plastic opening tool between the rear panel and the top case. Pry the opening tool upwards to separate the top case from the bottom case.
- Slide the opening tool along the case perimeter to loosen the bottom case.
- Gently pull the bottom case away from the laptop.
Insert a plastic opening tool between the rear panel and the top case. Pry the opening tool upwards to separate the top case from the bottom case.
Slide the opening tool along the case perimeter to loosen the bottom case.
Gently pull the bottom case away from the laptop.
Step 3
- Remove the four 1.2 mm Phillips #00 screws around the battery.
Remove the four 1.2 mm Phillips #00 screws around the battery.
Step 4
- Pull the battery cable out from its motherboard socket.
- Pull parallel to the motherboard, not straight up.
- Remove the battery.
- Disconnect the power cord from the battery and transfer it to your replacement battery.
Pull the battery cable out from its motherboard socket.
Pull parallel to the motherboard, not straight up.
Remove the battery.
Disconnect the power cord from the battery and transfer it to your replacement battery.
Step 5
Ventilation Fans
- The two ventilation fans are secured with the system by 5 screws. Unscrew these five 1.2 mm screws using the Phillips #0 screwdriver.
- When removing the screws, use a magnetic screwdriver to prevent the screws from falling behind the motherboard
The two ventilation fans are secured with the system by 5 screws. Unscrew these five 1.2 mm screws using the Phillips #0 screwdriver.
When removing the screws, use a magnetic screwdriver to prevent the screws from falling behind the motherboard
Step 6
- After removing all 5 screws, the fans are still connected with the system through 2 cables.
- Carefully pull the fan cables out of the connectors on the motherboard.
- Be cautious when pulling by the wires, this can permanently damage the fans beyond repair.
After removing all 5 screws, the fans are still connected with the system through 2 cables.
Carefully pull the fan cables out of the connectors on the motherboard.
Be cautious when pulling by the wires, this can permanently damage the fans beyond repair.
Step 7
- The fans can now be removed from the device.
The fans can now be removed from the device.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
4 other people completed this guide.
Author
with 3 other contributors
vangnam
Member since: 10/19/2017
592 Reputation
4 Guides authored
Badges:
14
+11 more badges
Team
UMass Dartmouth, Team S6-G7, Rockett Fall 2017
Member of UMass Dartmouth, Team S6-G7, Rockett Fall 2017
UMASSD-ROCKETT-F17S6G7
3 Members
7 Guides authored
